Other Accessories
714 topics in this forum
-
- 1 reply
- 232 views
Hello, I’m considering to upgrade my mother anat A8 plus motherboard. I wondered if the SKR MINI E3 V3.0 board could fit with this printer even with some adaptations? Thank you for your answer. ST
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
Last reply by BIQU info, -
-
- 1 reply
- 212 views
I'm needing to get a new mainboard for my Ender 6 and since I've upgraded almost all of it with Bondtech and TH3D parts (including TH3D'S unified2firmware), I'm wondering if the BTT SKR MINI E3 V3.0 will be compatible with them.
Last reply by BIQU info, -
-
- 1 reply
- 185 views
I recently installed the BTT mini 3.0. I downloaded the firmware here. When the machine starts, the hot end starts heating up and doesn't stop. It never did this with the oem 4.2.2 board. Has anyone every experienced this?
Last reply by BIQU info, -
- 1 reply
- 203 views
I find there is no voltage at the 5V pin of the Octopus 1.1 EXP1 connector, so no LCD screens hooked up to EXP1 and EXP2 will function. Is there something I need to do to enable these ports?
Last reply by BIQU info, -
- 7 replies
- 663 views
Hey I ordered my Biqu B1 and put it together myself. When I first turned the printer on, an error popped up on the screen saying the type C cable wasn't inserted well onto the hot end, so I turned off the printer, and re-plugged in the type C cable. Everything else after that was fine for a couple of weeks, and all my functions worked fine. Later, when I wanted to relevel the bed, the error that my type C cable isn't inserted correctly came back on, and I did the same thing as before. I turned the printer off and re-plugged in the printer, but this time the error did not go away. Every time I tried level the bed, the error would come on, and when I pressed for the printer…
Last reply by BIQU info, -
- 2 replies
- 128 views
Mornin Folks; gonna sound like a newbie here. I have an Octopus Pro Controller in the process of being wired to a harness for my Voron 2.4. the wire connectors on the harness are too small for the board so trying to change them over and I can't figure out what the size of the 2-pin wire connectors are to order. Any hints?
Last reply by BIQU info, -
- 1 reply
- 132 views
I have installed the mini SKR E3 V3 and lcd combo in my Ender 3. Initially when I hooked up the LCD I didn't install the TFT ribbon. the LCD seemed to work fine, touch screen or knob. However, it said no printer attached. Once I realized I hadn't hooked up the TFT ribbon and corrected this, the touch and knob no longer functioned. Attempted to reload the firmware and TFT files. Now I get the notification, "Found Outdated Data". Asks you to load the SD card and use the reset button. No matter what I do it stays the same now. Have tried many times to reload the Firmware and TFT files from the downloads. Does anyone have any suggestions. Haven't received any response from te…
Last reply by BIQU info, -
- 1 reply
- 228 views
I bought your version V2 before I read that it doesn't fit the Saturn 2. I'd love to have one of these but can't find one anywhere except from one company that is gouging the price. Any plans to make one? I think it's 230x129. Thanks, Greg
Last reply by 456er, -
Have two Ender 3 Pro's with upgraded BIGTREETECH SKR Mini E3 V3.0 Control Boards. Decided to add BIGTREETECH TFT35 E3 V3.0.1 Touch Screen Displays. Installed touch screen and updated firmware to 1st printer with no problems. Installed 2nd printer and I get "no printer attached" message. Tried changing BAUD rate with no results. To see if the display board was faulty, I switched display boards and get same error. Marlin mode works. I switched the 5 pin serial ribbon cable and got it to work. I've contacted BIQU to try to get a replacement. In mean time to purchase a replacement, what part number, description, specification or link to buy another. Thanks
Last reply by Primo Designs, -
- 2 replies
- 191 views
Buongiorno, Ho acquistato tramite il sito 3D jake una scheda madre BTT SKR2 rev b insieme ai TMC 2209 e un LCD BTT TFT35. Ho montato tutto, ho compilato il firmware e ho provato a caricarlo tramite microsd sulla SKR2 ma inizialmente non lo caricava, controllando il file nella microsd tramite PC era sempre in formato .bin invece che .cur Dopo diversi tentativi il file è diventato .cur però all'accensione lo schermo LCD della stampante ha mostrato svariati errori: -error "ALL LOW" -error "Impossibile abilitare il livellamento del letto" -echo: "mesh non valido" -error "Errore dimensione dati EEPROM" che poi dall'elenco notifiche è sparito Sembra …
Last reply by umberto, -
- 1 reply
- 286 views
I have a PI TFT50 v3.0.1 touch screen hooked up to a Rasp PI 4 running Klipper and a Octopus Pro v1 board. I got it all hooked up, tested it and now the touch screen shows all of the actions but the touch screen is unresponsive when I try to click a button. Not sure if there is some kind of software/hardware lock on the screen, but I am unable to get it to work.
Last reply by BIQU info, -
- 1 reply
- 162 views
I have added a plug on to my hot end fan at the fan end so that if the fan fails its easy to change and if I measure the voltage across the plug without a fan plugged in it reads roughly 22V, if I plug in a fan then it reads 1.5V and the fan doesn't spin. The fan works fine when I supply it with 24V from another fan socket, so its not a dodgy fan. What is going wrong? I bought the board back in May and its worked fine until this weekend when I started getting this issue. Unplugged fan Picture Plugged fan picture
Last reply by BIQU info, -
- 1 reply
- 167 views
I have a ender 3 pro and the extruder is too close to the bed. I need help making it so i can print with it off the bed any tips?
Last reply by BIQU info, -
- 1 reply
- 158 views
I bought a SKR3 to upgrade my current set up and I cannot get a known working Bigtreetech TFT 3.5 v3.0 touch screen to work. The power light on the TFT is on and it does beep but the screen is totally dark. Please advise what to do to get this display to work with this board.
Last reply by BIQU info, -
- 1 reply
- 192 views
Greetings- I have a Wanhao D6. The motherboard failed for the third time and I would like to replace it with a quiet 32-bit board. I am open to suggestions. What I have read so far is the the SKR 1.4 board is a popular replacement. Besides the board and the 2209 drivers, what else do I have to order. I assume I will need to replace the LCD. Is the LCD12864 plug-and-play? If not, is there an LCD that is plug-and-play? Finally, what else will I need to order to make a working printer. Thanks for reading, -Mark
Last reply by BIQU info, -
- 0 replies
- 121 views
Hello, I purchased the above a few months ago and recently tried to install them in my currently DOA CR-10v3. After swapping out the board and the display I get a constant beep from the display. I have tried connecting the SKR to all three of the EXP ports on the display and the TFT -> RS232 port. The only positive result I get is connecting EXP1 to EXP1 but with the RS232 not connected, at which point I get a short beep that fades out, but at least I get the screen to show the logo followed by the option to select the default Merlin layout or the BTT touch screen layout, but I get no response from the dial...likely because the RS232 port is not connected. The…
Last reply by sirtuxor, -
- 1 reply
- 153 views
Hey, I'm trying for the life of me to get this touch screen system to work. I put this in my ender 3 v2, and was planning on just using the touch screen so I have it all hooked up, can even access marlin mode. But no matter what I do for setting it up I keep getting no printer attached. All the wiring is good the display settings match to each other. Does anyone know how I can fix it?
Last reply by BIQU info, -
- 1 reply
- 222 views
I recently purchased a BIQU BX 3dD printer. I followed the directions in the manual and was well pleased at the quality of the benchy test file. I tried to print some other files (that I had successfully printed on an old i3 clone, but the prints all failed due to lack of adhesion to the build surface ( I had the same result when I pre-applied glue stick to the print bed). I also tried to print the drawer file provided by biqu with the same result. Any guidance to rectifying this issue? Thanks
Last reply by BIQU info, -
- 1 reply
- 190 views
Hi! I was using my printer but now an error appears. I try to solve this restarting the printer but the error is still there. Could you please help me with this matter? Thanks! Carla Error: Printer halted. kill() called!
Last reply by BIQU info, -
kevin hill
by Kevin- 1 reply
- 109 views
Hi, i recently purchased a BiQu B1 printer from my local Micro Center. I brought it home assembled the printer and was excited to print the first test file Pokémon. The print was successful. i moved on to the second test file included with the printer and the printer "halted" just above the ears on the bear. Since then I have not been able to get a successful print no matter what it is i attempt to do. i continue to get error messages "Printer halted. kill( ) called !" i am out of ideas with this machine. i believe that either the hot end or thermistor is bad on a brand new machine. i strongly disagree with purchasing new parts for a machine less then 2 weeks old. so, the…
Last reply by BIQU info, -
- 8 replies
- 398 views
Hello good afternoon. I had changed the extruder nozzle and turned it on normally, but I had forgotten to connect the extruder power cable. I turned it off and connected it, but when I turned it on, the screen didn't turn on anymore, the source works, the power is correct but it doesn't turn on anymore. what should I do?
Last reply by BIQU info, -
- 0 replies
- 92 views
Hello,I bought BTT SKR 1.4.Can You please give me information, how to config double x-axis with this board in Marlin firmware version 2.0.8.1 using X and E0?I cannot find any information on internet how to do this.The same config I have in MKS SGEN L v1.0, Marlin v2.0.8.1 with X and E0 and work great.SincerlyMiroslaw
Last reply by Miro, -
- 2 replies
- 264 views
I recently installed a H2 v2 hotend setup on my Creality CR10-v2. I had to swap some of the wires around on the stepper motor to get it to opportate in the correct direction. The gears move freely when moving manually. When attempting to have stepper extrude, the main gear keeps shuttering up and down and does not move smoothly. How do i resolve this issue?
Last reply by Biniecki, -
- 0 replies
- 123 views
I was wondering if there is a expansion board available for the Mini e3 v3.0 I would like to add a independent dual z instead of running them in parallel.
Last reply by Shwiboo, -
- 3 replies
- 282 views
I’m following the guide and attempting to load firmware but it’s not taking. I use SCP to pull it off the board and change the name to firmware.bin and tried multiple different cards, capitalized firmware and used a formatting tool also. Additionally I can’t get 5v power via usb even with the jumper.
Last reply by bustedparts,
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
- 2 replies
- 127 views
-
- 0 replies
- 5 views
-
- 0 replies
- 12 views
-
Hurakan included SD card requires format for Windows to recognize, cannot connect to WIFI
By Alen Burnside,
- 0 replies
- 15 views
-
- 0 replies
- 25 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
