Other Accessories
713 topics in this forum
-
- 2 replies
- 169 views
Hello, I need to connect a K thermal probe using a MAX31855K chip to a SKR1.4 Turbo Board ans SPI protocol using MISO, SCLK and CS Pins. I don't find any information about it in Internet in order to configure Marlin software and where connect SPI pins from the breakout board to SRK1.4 connectors. Please could you address me in some Internet place or send some white paper whereget all information about software configuration an assembly of the K Thermal Probe. Many thamks in advance for the collaboration and best regars Enrico
Last reply by Enrico, -
-
- 1 reply
- 117 views
Hallo ist hier jemand der mir erklären kann wie ich die RatOs Software auf das SKR 3 EZ installieren kann Die Image Datei habe ich auf dem Raspy benötige aber noch die Software für das Board Danke für eure Hilfe
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
Last reply by BIQU info, -
-
-
- 3 replies
- 198 views
Hello I need to replace the main board on my Biqu BX with another one with at least 6 drivers so I can use a H2 500C that requires a driver slot for the PT100 amplifier. Do you know any boards that would be a plug-and-play replacement? Thanks in advance
Last reply by BIQU info, -
-
-
- 1 reply
- 143 views
On November 7 I made a support ticket 861, and I still do not receive a response from it, could you please respond, the service is very bad, so that make me seriously think about continuing to purchase products of your brand. Thank you
Last reply by BIQU info, -
-
-
- 1 reply
- 140 views
There is a brunt chip on this board I just bought is there a way I can fix this?
Last reply by BIQU info, -
-
- 1 reply
- 110 views
HI, Im considering buying a BIGTREETECH SKR Mini E3 V3.0, or something similar for my ender 3 pro. I would really like to add dual extrusion to it. is it possible to set the firmware up on SKR Mini E3 to run dual extruders, with something like this hot end? https://www.amazon.com/gp/product/B082PV116C/ref=ewc_pr_img_2?smid=A3LD44RLMMOM6N&psc=1 Its a 2 hotend type incase you didn't want to click the link. If it is possible could someone please share a link or something with a good place to learn more? Thanx Guys
Last reply by BIQU info, -
- 1 reply
- 174 views
I have the SKR MINI E3V3 control board on my cr10s works great, what I need to know is is the 5v plug hot when the turn the printer on? I need a 5v supply for a temp Ga I run on my printer.
Last reply by BIQU info, -
- 1 reply
- 412 views
Hi! I have to connect to printer via ssh from my computer for input shaper etc... what are the default username and password?
Last reply by BIQU info, -
-
- 2 replies
- 82 views
Can the SKR 3 receive a 5v input voltage return on the 5 v out line on the z stop 5v pin. Reason I ask is I want to use an optical sensor and it returns voltage along VCC Sensor: OPB990P51Z
Last reply by BIQU info, -
-
Thermal Runaway
Last reply by BIQU info, -
-
- 1 reply
- 106 views
Hallo in die Runde Ich habe ein SKR 3 EZ Board benötige eigentlich 6 Treiber für meinen RatRig V Core 3.1 es hat aber nur 5 Treiber aber Z Motor A , Z Motor B , und E1 funktioniert das mit Klipper? Und wo werden die 12V Lüfter für die Bauteilekühlung und den Mainboardlüfter angeschlossen und wie müssen die Jumper gesteckt werden für 12V und wo wird der 24V Heatbreak Lüfter eingesteckt? Danke für Eure Hilfe Gruß Jörg
Last reply by BIQU info, -
-
-
- 1 reply
- 110 views
Hello I purchased a H2 500C thinking that would be a plug-and-play replacement for the one that come with the BIQU BX but it seems to require a different termistor and a driver. I saw the document for the MAX31865 but it seems it requires a free driver on the controler and, in this case I can't use on the Biqu BX without replacing the mainboard as well? Thanks in advance
Last reply by BIQU info, -
-
Hello, I am trying to update this screen, which I will send pictures in the attachments. The update is not completed, and this is what it tells me in the picture. The details. I am annoyed. Do you have a solution? I hope so.
Last reply by BIQU info, -
- 2 replies
- 206 views
I changed my main board in my Ender 3 V2 to an SKR E3 V3.0. I am unable to get my CR Touch to operate the Z end stop. I have spent a week try as many ways as suggested by those that appear to have the same problem. I have tried connecting the two wires from my CR Touch to the Z stop but that does not work, If I connect the original micro switch that was fitted to the printer before I fitted the CR Touch I can simulate the Z homing. I have tried to compile Marlin firmware but probably lack sufficient knowledge to achieve that but I followed an online guide and although it compiled it made no difference. Can anyone tell be if the two wires, red and blue from a CR Touc…
Last reply by Stolowma, -
- 1 reply
- 169 views
Can you still run klipper on this board with an external raspberry pi (not a connected module)?
Last reply by BIQU info, -
-
- 1 reply
- 188 views
Hello, I would like to use the temperature sensor as PT100 in EBB36 v1.2. But there was a problem, and I couldn't find what the problem was, so I'm asking you this question It's a 4-wire PT100, and I think the DIP switch and Klipper settings are accurate, but why not?
Last reply by BIQU info, -
-
- 1 reply
- 105 views
Hello, I'm having problems with my smart sensor, I recently bought it and installed it on my biqu b1 printer, but it doesn't work, it starts printing 10s later to warn me of filament runout, could anyone help me?
Last reply by BIQU info, -
- 1 reply
- 274 views
recently purchased this screen and flasheed with marlin software from V1. in marlin mode it homes and moves the machine just fine but displays no mediawhen trying to run g-code. in touch mode it recognizes thee sd card but top of display says no printer attached.
Last reply by BIQU info, -
- 1 reply
- 135 views
I’m trying to cut down the fan noise of my Ender 3. The steppers are basically silent now, which is thanks to the SKR Mini E3 V3, but the fans are still loud. I’d like to remove the active cooling fan that’s in the main board housing. I’ll probably print a better vented top panel too. Does anyone have experience with how much heat the main board generates, or if it even needs active cooling? Thanks in advance!
Last reply by BIQU info, -
- 1 reply
- 196 views
Can you run an Octopus Pro 446 using the CB1 with adapter as the Pi replacement? I had an rPi 3B+ but for some reason it will no longer connect or show on my network I purchased the CB1 with Adapter hoping to swap them out, after reflashing TIA
Last reply by BIQU info, -
-
- 2 replies
- 384 views
Hi everybody, I have a SKR mini E3 V3 on my homemade printer (Rolohaun Bijou) and I am having a very troubling issue with endstop configuration in Marlin (Bugfix 2.1.x nightly). I have the endstop pullups enabled, homing direction set to min on all axis, and endstop pin set to Use_[axis]_min_plug. All settings identical to the official BIQU Ender 3 firmware on github. When using M43 to debug pins, the pin states for the endstops report as triggered at all times, and does not change with the switch being pressed. Does anybody have any ideas as to what may be the culprit? I have tried just about everything under the sun! Thanks!
Last reply by BIQU info, -
-
- 1 reply
- 137 views
good day . i have purchased the BTT Mini UPS 24V V1.0, for a Ender 3v2 printer , followed the connection instructions as per BTT Mini UPS 24V V1.0 wiring documents . when its connected and i turn on the power, the printer does not fully turn on it lights up for few seconds then turns off it constantly does this and does not full power on. when i remove the BTT Mini UPS 24V V1.0 the printer powers on as per normal then I'm able to connect the BTT Mini UPS 24V V1.0. is there a way to keep the BTT Mini UPS 24V V1.0 connected and the printer power on normally ? any help would be appreciated thank you
Last reply by BIQU info, -
- 1 reply
- 104 views
When my BIGTREETECH UpgrSKR Mini E3 V3.0 Silent Board 32bit Motherboard goes to heat up it doesn't stop at preset temperature just keeps going how do I fix?
Last reply by BIQU info, -
- 1 reply
- 159 views
Have the mini E3 v3 board and Tft32 display. Added an all metal hotend. trying to get hotend to 300deg recompiled firmware, firmware successfully runs but temp still limited to 270deg. Found out display also limited temp over rideing controller firmware. Re-edited display to 300 then 320 just to try it. Tempiture got to 290 will not go higher? Where is this limit?
Last reply by BIQU info, -
-
- 3 replies
- 143 views
Hello, I have a question. I want to use SKR3 EZ to power 5v power to GPIO on Raspberry Pi. So which connector on the SKR3 EZ should I get the 5v output from? Can you recommend?
Last reply by BIQU info, -
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
-
Popular Topics
-
- 0 replies
- 8 views
-
- 1 reply
- 91 views
-
- 1 reply
- 143 views
-
- 1 reply
- 50 views
-
- 0 replies
- 23 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
No files have been downloaded yet this week.
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
