Jump to content

Other Accessories

713 topics in this forum

  1. Stevew

    Octopus v1.1 f446 pin out diagram

    by Stevew
    • 1 reply
    • 1.1k views

    Hey all, I am about to install an octopus v1.1 f446 chipset into my ender 5 plus and am trying to find a klipper printer.cfg that has setting for TMC2209 drivers and a pin out diagram for this board. any help Is truly appreciated. many thanks

    BIQU info
    Last reply by BIQU info,
  2. su541

    Upgrading a Sidewinder X1 to H2(o)

    by su541
    • 1 reply
    • 154 views

    Hi, i think about changing the extruder of my sidewinder x1 with the H2O. In the same step, i like to add "Auto-Power Off". Because the Sidewinder uses a MKS GEN L Board, i think also need to upgrade the controllerboard. The actual display is a TFT28 (MKS). What board do you prefer? At the moment i think about the SKR 3. But I'm not sure, if also should by the BTT TFT28 Display? Best reguards

    BIQU info
    Last reply by BIQU info,
  3. bustedparts

    SKR Mini E3 V2.0 firmware building.

    by bustedparts
    • 1 reply
    • 104 views

    I bought this board so I can use my printer while I wait to get a replacement CB1 . I am attempting to build a firmware for it to run my Clone I3. So I am going to use the example file for folgertech i3 and I have run into my first roadblock . In the first part of marlin firmware yoou have to call out the type of board your using. There used to be a file in marlin that was called boards.h and it listed all the compatible boards used with marlin. I no longer can find this file and I need to know the boards name so it works properly. I am finding loads of videos on how to install this board on Ender printers but I could not find any for doing a custom installation. I am a…

    BIQU info
    Last reply by BIQU info,
  4. valleybowhunter

    Ender 3 pro BL touch firmware octopus

    by valleybowhunter
    • 1 reply
    • 219 views

    Would someone be able to share a firmware file for a Ender 3 pro with BL touch running Marlin on the octopus? I'm just learning how to read/write the firmware files and was hoping someone could help out. Wasn't able to locate the octopus listed under the premade configuration files for my printer. Unless i've overlooked something. ( likely ) Thanks!

    BIQU info
    Last reply by BIQU info,
  5. mike Coleman

    skr 1.4 z axis issue

    by mike Coleman
    • 1 reply
    • 225 views

    when printing a 20x20x20 cube the z prints 40mm #if AXIS_IS_TMC(Z) #define Z_CURRENT 800 #define Z_CURRENT_HOME Z_CURRENT #define Z_MICROSTEPS 16 #define Z_RSENSE 0.11 #define Z_CHAIN_POS -1 //#define Z_INTERPOLATE true //#define Z_HOLD_MULTIPLIER 0.5 * Default Axis Steps Per Unit (linear=steps/mm, rotational=steps/°) * Override with M92 * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]] */ #define DEFAULT_AXIS_STEPS_PER_…

    BIQU info
    Last reply by BIQU info,
  6. tmmchero

    Manta m4p with cb1 using input shaper

    by tmmchero
    • 1 reply
    • 409 views

    i am having trouble getting the input shaper function to work, i keep getting MCU protocol error MCU Protocol errorThis is frequently caused by running an older version of thefirmware on the MCU(s). Fix by recompiling and flashing thefirmware.Your Klipper version is: ebc3b0dMCU(s) which should be updated:mcu: Current version v0.10.0-317-gb4b19b8fUp-to-date MCU(s):CB1: Current version ebc3b0dOnce the underlying issue is corrected, use the "RESTART"command to reload the config and restart the host software.mcu 'mcu': Unable to extract params from: config_spi also i am having trouble finding any documentation on the subject as far as dtb file i need…

    BIQU info
    Last reply by BIQU info,
  7. Adriano

    Printer not connected error message

    by Adriano
    • 1 reply
    • 100 views

    I had the printer turned on by accident, the type C connector disconnected and now the printer no longer works and I get a message "printer not connected" "Error printer halted. kill called" please help I don't know what else to do

    BIQU info
    Last reply by BIQU info,
  8. secretreeve

    ender 3 pro, skr mini e3 V3 temp drops after starting print

    by secretreeve
    • 0 replies
    • 246 views

    ok so i have a standard e3p with the skr mini e3 V3 installed, everything is wired up properly, i actually run 3 of these printers all with the same board, same setup, same everything, except this one particular printer, once it gets up to print and begins the job, the hot end temp drops till it just reboots itself. i can bring it up to temp and let it sit there and get no problem, it seems its only when it begins the print job it actually starts to loose temperature. it was working perfectly fine before replacing the board and i have had successful prints so this is a new development.

    secretreeve
    Last reply by secretreeve,
  9. Cook91c

    Skr mini e3 v3 freeze

    by Cook91c
    • 6 replies
    • 1.1k views

    So I have a skr Mini e3 v3 with a Tft35 e3 v3.0.1 installed on my ender 3. Printer also has meanwell lrs 350-24, Dual z using both z plugs on bored and biqu h2. When I installed a bltouch v3.1 and upgraded firmware all my problems started. I get random freezing mid print. Tft35 will not respond at all. Hotend and bed continue to hold temp but there is no x y or z movement. I've tried several different bltouch firmware with same results. I can switch back to original firmware without bltouch and freezing goes away. Any recommendations on what I can do to resolve this issue?

    n0tr3adY
    Last reply by n0tr3adY,
  10. Jason Badon

    MKS Robin Pro and TMC2209 && EZTMC2209

    by Jason Badon
    • 1 reply
    • 164 views

    When I configure my jumper for UART mode I get the error "TMC CONNECTION ERROR", Does this need me to make the serial connections as well? What about the EZTMC2209? There are no connections for them at all. Thank you, Jason

    BIQU info
    Last reply by BIQU info,
  11. Berkus Decker

    BIQU H2 V2 operating voltage

    by Berkus Decker
    • 1 reply
    • 250 views

    Hi! What is the supported extruder motor voltage? Manual says 3.45V but all the boards I know supply 12V or 24V to the extruder motors.

    BIQU info
    Last reply by BIQU info,
  12. Bcorre

    H2V2S REVO EXTRUDER FOR BIQU B1

    by Bcorre
    • 1 reply
    • 244 views

    I just received my H2V2S revo extruder and printed the parts from biqu website BUT I CANNOT FIND INSTALLATION/BUILD INSTRUCTIONS ANYWHERE! Nothing in YouTube but the h2 extruder which is the older model and not the same! I need a tutorial video and or instructions in English in order to build and install my H2V2S revo extruder on my biqu b1, have it all disassembled and I am stuck in the mud. Please help thanks!

    BIQU info
    Last reply by BIQU info,
  13. Biniecki

    H2V2 constantly jams

    by Biniecki
    • 1 reply
    • 209 views

    I have been fighting an ongoing issue with the extruder since I got it. I can't print for more than about 5 to 10 mins without getting a jam. I have PID tuned hotend, calibrated esteps, and heat tighened the thoat and nozzle. My retraction settings are .8mm @ 25mm/s. I also thought the smart sensor was possibly giving false possitives but when I turn it off I find it jammed printnig in mid air. Im at a loss as to what else could be causing the problem

    BIQU info
    Last reply by BIQU info,
  14. rikardo

    Biqu H2 V2 with Biqu B1 SE PLUS and installation

    by rikardo
    • 1 reply
    • 126 views

    Hello, can I use the Biqu H2 v2 extruder with the B1 SE PLUS 3d printer? If yes, how to install it. Thanks in advance.

    BIQU info
    Last reply by BIQU info,
  15. Peter

    Biqu H2 V2S Lite Thermistor Type

    by Peter
    • 3 replies
    • 392 views

    Hello, trying to get the PID Values: SENDING:M303 E0 S200 C8 PID Autotune start PID Autotune failed! Temperature too high One possible Problem might be the Thermistor Type. Manual says NTC100K. I configured Type 1 (EPCOS). In Marlin there are about 30 different to choose. Which Type is the one delivered with the Extruder? Thanks, Peter

    BIQU info
    Last reply by BIQU info,
  16. BigO

    H2O

    by BigO
    • 1 reply
    • 160 views

    Im currently finshing a ender 5 plus H2O converstion. now that im at the firmware im a little confused on the marlin programming for the supplyed 3 wire thermister. Im hope to use the SKR 3 ez with tmc2209ez steppers that i have. my question is, with the skr 3 ez do i still need the Max31865 driver? i dont think i do with the skr3 but the manuals dont say much. i just dont want to let the magic smoke out of the board.

    BIQU info
    Last reply by BIQU info,
  17. Christian Murphy

    HDMI5 Brightness Control

    by Christian Murphy
    • 1 reply
    • 113 views

    Looking to be able to put a HDMI5 completely to sleep including turning off the backlight. This must be done programmatically or through power management and not the buttons on the display. Thanks for any help!

    BIQU info
    Last reply by BIQU info,
  18. Stolowma

    TFT35 not displaying layer height properly

    by Stolowma
    • 1 reply
    • 160 views

    I have a TFT35 hooked up to a SKR mini E3 V3 and everything works except the layer height display. It shows the height in mm but the number of layers as ----. I contacted support and tried everything they recommended including updating the firmware to one they sent me with no effect. Anyone else had this problem?

    BIQU info
    Last reply by BIQU info,
  19. Stolowma

    Homing issues

    by Stolowma
    • 1 reply
    • 180 views

    My E3 Pro with a SKR Mini E3 V3 board has suddenly started having a problem with homing the X & Y axis. I printed a week or so ago and it worked fine, turned it on the other day and can't get past the auto home sequence. The X if you home it individually works as it should but with auto home it moves over until it clicks the stop switch, moves away as usual, then moves back into the switch and the servo keeps running until you shut the printer off. I checked the switch and even though it seemed OK I replaced it but didn't solve the issue. The Y goes to home, hits the switch and keeps going until you shut it off. The Z seems OK but I only tried it a few times because …

    BIQU info
    Last reply by BIQU info,
  20. bustedparts

    Manta MP4 with CB1 web interface refuses to connect

    by bustedparts
    • 4 replies
    • 399 views

    I was able to connect to the web interface 1 time and after that it will no longer connect. I can ssh into the board and it is on my network . But I will not connect to the web interface. I have nothing else connected to the board at the moment. I tried chrome and microsoft edge and none will connect. It says it is refusing the connection. I dont know what else to try so I am here looking for help. I do have Klipper ,moonraker and mainsail installed and i have updated them. Still no web interface.

    BIQU info
    Last reply by BIQU info,
  21. khitsicker

    Marlin wont compile for BTT SKR mini e3 v3

    by khitsicker
    • 1 reply
    • 228 views

    I am having an issue trying to compile Marlin for a SKR mini e3v3. I am getting errors saying there are missing files. I have tried manually creating the folder in the error logs and placing the missing file but it has not solved the issue. The error is as follows: [Errno 2] No such file or directory: 'C:\\Users\\user1\\.platformio\\.cache\\tmp\\pkg-installing-rkyy3z6r\\Arduino_Core_STM32-main\\variants\\STM32MP1xx\\MP133AA(E-F-G)_MP133CA(E-F-G)_MP133DA(E-F-G)_MP133FA(E-F-G)_MP135AA(E-F-G)_MP135CA(E-F-G)_MP135DA(E-F-G)_MP135FA(E-F-G)\\PeripheralPins.c' any suggestions would be appreicated.

    BIQU info
    Last reply by BIQU info,
  22. Allan Penston

    MR

    by Allan Penston
    • 1 reply
    • 147 views

    can you use a skr e3 v3 motherboard on a cnc3018 router/engraver.

    BIQU info
    Last reply by BIQU info,
  23. dumknight

    Manta m4p with Ender 7 External Stepper Drivers

    by dumknight
    • 1 reply
    • 386 views

    Hello friends, I have a Manta M4P installed in my ender 7. With a Cb1 and klipper. I currently have it running with tmc2209s bypassing the DM542 chonky stepper drivers built into the machine. If I wanted to use the external stepper drivers (that go up to 4amps). how would I go about that ? what would the jumper configuration be? what stepper would I need to put into the pin slot? Thanks in advance. not much documentation out there about external drivers except when using an arduino mike

    BIQU info
    Last reply by BIQU info,
  24. jirby

    BIGTREETECH Gen v1.0

    by jirby
    • 1 reply
    • 240 views

    hi I need support for this BIGTREETECH Gen v1.0 card I can't find anything to be able to configure correctly

    BIQU info
    Last reply by BIQU info,
  25. cubalibreee

    SKR 3 EZ V1.0 no Windows 10 to SD no connection

    by cubalibreee
    • 1 reply
    • 202 views

    Hello, is it no longer possible with the SKR 3 to access the SD directly via windows? I get just MARLIN_STM32H743VX CDC in FS Mode connection! regards from Germany...

    BIQU info
    Last reply by BIQU info,
×
×
  • Create New...