Other Accessories
712 topics in this forum
-
- 1 reply
- 170 views
Creality Ender 3 max upgrade below parts and then got the 2 problem! 1，Original Creality direct drive 2，CR touch, 3，Bigtreetech skr mini E3 V3.0.1 controller 4，Bigtreetech TFT35 E3 V3.0.1 touch screen. Now the problem as below: 1, TFT35 Touch screen graphic mode can not use and show "no printer attached" but Marlin mode is work, motor, CR touch, Fan… 2, Marlin mode hotend preheat the machine will be auto restarts, however preheat the bed is fine
Last reply by BIGTREE TECH, -
- 1 reply
- 193 views
I am looking to purchase a new direct drive extruder on my Anycubic Chiron. Does anyone have a mounting bracket for it that I could print?
Last reply by boanerges57, -
- 0 replies
- 112 views
Hello, I have an SKR 1.4 turbo mounted on ender 3 pro running on marlin firmware. When i am trying to do an ABL leveling the procedure starts normal and as always first goes to zero on every axis. After that it moves to the beggining of the bed and starts going on each point of the bed. It makes first 3-4 points correct until it reaches maximum X value then it moves the Y axis (the bed) forward and starts to do second row but then it doesnt move X in the other way. As a result the hotend crashes at the end of the X axis. Thats when i cut the power and start all over again. I moved the X axis using the touchscreen all the way to the right and then all the way to the l…
Last reply by Crden, -
- 0 replies
- 73 views
I'm setting board for a laser that needs 5v PWM. Is there a way to do this with E3 RRF V1.0 Thanks
Last reply by PLASTIC55, -
- 0 replies
- 193 views
I am running a Pi4-B adapter and CB1 board. Is there a way to disable power from the USB ports? I don't want my display lit when power to the printer is shut off since I am running Octoprint on the board.
Last reply by Ryan James, -
- 1 reply
- 214 views
Page 12 of the manual shows the voltage select jumpers but nothing is labeled!!! How do I set my motors to 24 volts if nothing is labeled!!
Last reply by CandidQuality, -
- 0 replies
- 141 views
Having some trouble with a BLTouch on a Octopus v1.1 I have it wired to the probe port and the test functions BLTOUCH_DEBUG COMMAND=pin_down BLTOUCH_DEBUG COMMAND=pin_up BLTOUCH_DEBUG COMMAND=touch_mode all work but when I QUERY_PROBE I always get Open even thought the BLTouch is changing state. [bltouch] sensor_pin:^PB7 control_pin:PB6 x_offset: -44.0 y_offset: -9.0 z_offset: 0.0 [homing_override] gcode: G90 ; Use absolute position mode G1 Z10 ; Move up 10mm G28 X Y G1 X200 Y200 F6000 ; Change the X and Y coordinates to the center of your print bed G28 Z set_pos…
Last reply by Andrew, -
- 0 replies
- 661 views
Booting the CB1 from the 4.9 Image was a breeze, I even managed to get wifi configured through the system.cfg file. HDMI out, on the other hand, has been less than stellar. I'm using an HP27f and the display is at 180 60HZ. My MAC is plugged into HDMI1 and the CB1+Pi4b adapter is plugged into HDMI2. On this display I get no display error, on my dell I get an error related to unsupported refresh rate. What can I do to change the display setting through either the system.cfg file or from a terminal. ------ hdmi_width=1920 hdmi_height=1080 hdmi_mode=60 check_interval=30 # 循环检测wifi是否连接,时间 30s router_ip=8.8…
Last reply by Alex Angelino, -
- 0 replies
- 521 views
Hello to all: I have a problem and trying for same days now to get it to work. First it runs fine but without sensor less homing then it printed fine. after a few tries i made a new marlin firmware and now the sensor less homing works but after that nothing seems to work i cant move any thing even when printing it doesnot move. M211 S0 doesnot help only homing works well skr pro v1.2 tmc2226 x6 sensor less homing and probing software endstops reprap touchscreen marlin 2.1.1 if i use the old bin it moves again but without homing so nothing is broke Can some one help me please thanks
Last reply by MakkeLeon, -
- 0 replies
- 312 views
The connector used on the BIQU BX Hotmode board is smaller than the standard connector on the Thermistor and Heater Cartridge replacements I've got. What type of connector is this? https://www.dropbox.com/s/6dw5e82t7omkewy/BIQU BX Hotmode Board.jpeg?dl=0
Last reply by Kile, -
- 7 replies
- 725 views
I currently have some of your boards on 2 Ender 3s with no ABL on them that run great. I also have a CR-10 with the EZABL from TH3d on it running a stock board but wanting to put the Mini E3 V3 board with a BTT touch screen on it. I would like to keep the EZABL that is already on it. So wondering if the TH3d sensor and the Mini/BTT touch screen can work together?? Thanks
Last reply by Luis, -
In regards the the GTR + M5. Very little is know about how to configure the M5 fans and setup the steppers. could you enlighten me as to the process?
Last reply by Zimmie, -
- 0 replies
- 125 views
I send a M115 command to my SKR 3 EZ using several different terminal emulators. They all are successfully connect to the board. I'm sure that the firmware loaded successfully as firmware.bin file changes to frimware.CUR on the SD card. I get a "Locked $" response to the command. What am I doing wrong?
Last reply by sheski3, -
- 0 replies
- 107 views
Hello! I have a SKR 2.0 running on Marlin and it was working perfectly until yesterday, during a 4 hour print at around 3 hours into it, the hotend just lost power and wont heat ever since. I have noticed that now, when I turn on the heat on it, the little LED on the board wont come on. Is there a fuse or something I could check related to the hotend or do you guys have any suggestion on what could be wrong? The thermostat works fine, and everything else on the board seem to work just fine. Thanks, cronvell
Last reply by Cronvell, -
- 0 replies
- 177 views
Hello everyone, I have been trying to install firmware for my new CR-touch but nothing from Creality is being recognized by my machine and I think it's due to having the TFT35 board. I have not been able to find any information on firmware for the Bigtreetech board to allow the CR-touch to be recognized. I thought I had read that the CR-touch would automatically be recognized by the Bigtreetech board as it has firmware for the BL touch and they work off the same generic firmware. Any help will be appreciated.
Last reply by Eric Vandever, -
- 1 reply
- 229 views
i have an ender 3 pro just installed the skr mini e3 v3.0. just added the cr touch and is not working. it is connected with 5 pin harness. ive tried all the firmware i could find. the videos that i have found show a much different pin out put. ive tried to repin it and got a blank screen. repinned it back and the screen was working. even tried to move the wires over to the z stop and nothing. i notices that the wires on my harness are a different color. they are blue red yellow blk and wht. in the videos its wht blk yellow red brown. any advice would be greatly appreciated
Last reply by fatboy1271, -
- 0 replies
- 113 views
I'm guessing my new SKR understands that my bed is 300mm x 300mm, because my BLTouch probes the full bed. However, when I select Leveling it gives me a 235mm x 235mm Grid with an offset of 30mm. I can't find in Marlin Firmware where to change this...? fat
Last reply by fatboy1271, -
- 1 reply
- 118 views
hi there just installed the bigtreetech skr mini 3.0 . having trouble getting the bl touch to work with it. tired all the firmware updates and nothing. i will home it and it will go to the center of the build plate. the probe will do its thing but the z axis will not go down to the build plate the i get the error code m999 restart. i dont know what that means.
Last reply by fatboy1271, -
- 1 reply
- 565 views
I was wondering what the LEDS on the mother board were for I can not find anything in your manuals on them. I am not sure if they will help solve my problem or not.
Last reply by BIGTREE TECH, -
- 0 replies
- 169 views
When I am doing commands in Pronterface, I am not getting any output. It is connected via USB and responds to commands, but just doesn't return any output. For instance, M303 E0 S240 will start PID tuning at 240 degrees. However the terminal in Pronterface remains empty except for the command text. M500 will produce a "Settings stored" message on the printer LCD. If I send M503, I get nothing back. SKR E3 Mini V3 on Ender 3 Max connected to Windows 10 computer via USB I am currently connected at 115200 baud rate, no other terminal connections are active. My marlin firmware: #define SERIAL_PORT 2 #define BAUDRATE 115200 //#define BAUD_RATE_G…
Last reply by Dapperdreadful, -
- 0 replies
- 119 views
I have an interesting problem. I use VAT because it is the only terminal emulator that sends lower case commands to enter my network password. I'm a mechanical engineer. No EE or CS degree. I can communicate using Prontoface or Putty, but no lower case. When I use YAT, I get no response from the SKR3. YAT shows that it is connected to the Com port with no errors. YAT DOES communicate with my SKR2. Suggestions?
Last reply by sheski3, -
- 1 reply
- 167 views
こんにちは、私は 初心者です。最近、プリンターを静音化とオートベットレベリングをするためにコントローラー ボード、SKR mini E3 v 3.0 とBLTOCHを購入しました。私はまだ経験が浅いので、発生した問題について助けを求めたいと思います。 マザーボードを交換し、BLTOCHも接続し、ファームウェアも書き換えたのですが、オートベットレベリングが実行されません。 一応curaにG28の後にG29を書き込んだのですが、それでも動きません。 何をどうしていいものか全く分かりません。 どなたかサポートデスクみたいな所をご存知の方は居ませんか？
Last reply by BIGTREE TECH, -
- 1 reply
- 132 views
As the title suggests, I'm a first-time user of the SKR board. I recently received a SKRPro-V 1.1 board from a co-worker to use with my Frankenstein printer that is based on an Ender 3 and I have some questions, the first of which is my coworker said that this is an SKR 2; however, the board itself says SKR Pro-V 1.1 is this the same thing or is he mistaken? also does anyone have any idea on a guide on how to install this to my ender 3? I also plan to install a cr touch and ender 3v2 touch screen display.
Last reply by BIGTREE TECH, -
- 3 replies
- 291 views
I bought an SKR Pico to replace the control board in my printer. It doesnt seem to work. I tried connecting over UART, Ive followed every guide I could find. The best I managed was getting it to connect one time and after being turned off overnight it has never been able to connect again. The RGB light also doesnt seem to light up ever and it does on the guides. I started out using stock firmware from BTT. Ive also compiled my own. Nothing seems to help. The one time it connected was with the firmware I made, but it has never worked again. I am using a good power supply and have checked my output voltage, current, and the stability of both. I have also tried a different p…
Last reply by BIGTREE TECH, -
- 1 reply
- 514 views
I'm trying to configure sensorless homing on the Pico. I cannot find what pin should I use for the diag_pin parameter: https://www.klipper3d.org/TMC_Drivers.html?h=diag_pin#configure-printercfg-for-sensorless-homing Has anyone got this working?
Last reply by BIGTREE TECH,
-
Popular Topics
-
- 4 replies
- 523 views
-
- 0 replies
- 30 views
-
- 0 replies
- 34 views
-
- 1 reply
- 37 views
-
- 6 replies
- 3,069 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
