Other Accessories
712 topics in this forum
-
- 3 replies
- 614 views
Hello all, just got the BTT s42c v1.1 kit off amazon. It came with no documentation. When I go to the BTT site I see a similar product which is version 1 I linked below. The kit below shows an aluminum alloy shell for the back of the stepper that the board mounts in. My kits are both missing those shells. Where can I get these shells and can I print them and where does the little magnet that comes in the kit go? I cant find anything online to help. I found a download that contains a pdf of so called instruction but ita VERY bleak and for the version 1. Not version 1.1. https://www.biqu.equipment/products/bigtreetech-s42c-v1-0-42-stepper-motor-closed-loop-driver-board…
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
Last reply by BIQU info, -
- 1 reply
- 2.8k views
I installed the BIQU H2 on my Ender 6 but I have some problems with extrusion. After having changed the e steps to 932 as recommended, I measured and in fact I needed 951. Extrusion was fine during the m92, but as soon as I start a normal print the filament jams in the nozzle and extruder motor skips steps. I have tried with brass and hardened steel nozzle - same problem. I have to disassemble the whole H2 to solve the problem. My settings were: Nozzle temp 200 C Speed 200 mm/s Retraction 1 mm Retraction distance 1 mm Could it be my settings? What are the recommended settings (it is my first direct drive try)?
Last reply by BIQU info, -
- 1 reply
- 227 views
Hello, Any had already tried to config a Duet 2 wifi with the BIGTREETECH MAX31865 V2.0 for BIQU H2 extruder? Any help will be great¡ Best regards
Last reply by BIQU info, -
- 1 reply
- 187 views
i need your help my printer wont home in any way its like the sensor is stuck or something . what can i do please i need your help
Last reply by BIQU info, -
- 1 reply
- 185 views
Red LED blink only once power goes to bl touch and display but that's all. Usb also don't react with PC. I did not find any description of this RED light blink only once. Thank you VID_20220620_193706.mp4
Last reply by BIQU info, -
- 1 reply
- 192 views
Hi I am after some advice on a alternative motherboard for ender 6
Last reply by BIQU info, -
- 1 reply
- 264 views
Hello everybody, hope you are fine Have you maybe already encountered this issue ? I am preparing the control system for my new VZBot330 printer For that I have one Octopus Pro with TMC2209 drivers and one Raspberry Pi 4 with the BTT Pi TFT50 V2.0 screen I have prepared the Raspberry without the screen, all updates and upgrades where pushed using WiFi As soon I connect the screen to the Pi I loose the Wiifi network and I could not find why and what tis the issue Any help will be appreciated
Last reply by BIQU info, -
Loaded a basic marlin 2.0.9.3 configuration: 1. Line 99 change the bd type to the "BOARD_BTT_SKR_V2_0_REV_B" 2. Line 110 change the serial port to "-1" 3. Line 864, 865, 866, 875, change to the "2208" stepper drivers I am using 4. Line 2475, enable "#define CR10_STOCKDISPLAY". I also changed to the correct environment: BIGTREE_SKR_2_F429, in platformio.ini. that works fine, I can move the steppers ok. But when I just change: Line 1834 #define EEPROM_SETTINGS, with that enabled I only get the marlin bootscreen showing marlin version. The system is an Ender 5 with the original LCD display. Configuration.h platformio.ini
Last reply by BIQU info, -
- 1 reply
- 219 views
Hello. I have a Bigtreetech TFT50 V3.0 that I can't seem to update firmware. I tried so far with 3 different memory cards, 2 are 128Mb other is 8Gb, all are fat32 formatted, with my own compiled firmware and with the firmware on BTT GitHub, to no avail. Any help appreciated.
Last reply by BIQU info, -
- 1 reply
- 337 views
After ramps 1.6, I switched to skr mini v1.1. But I don't know how to connect my Blutouch. Could you help? I don't know the Marlin and cable connections on this board.
Last reply by BIQU info, -
- 1 reply
- 364 views
I have an SKR 2 board and, I have gone through the steps to load my raspberry pi with octoprint and get Klipper loaded. I have made a klipper.bin file with the STM32 and 429 chip for my SKR 2 board. I successfully completed this process about a month ago on an skr 2 successful and had no problems but I am having no luck this time around. Issue: When I go to flash Klipper onto my board it takes about 1 second and both red lights show and so does the sd card light. But the green light next to the power input terminals never turns on and when testing the voltage to the steppers and fans there is less than 1 volt (about 300 mV). When checking the SD card the file is…
Last reply by BIQU info, -
- 1 reply
- 190 views
So, I've been working out the kinks of the GTR and TMC2209. I'm finding it seems like the GTR can't keep up with microsteps set above 16. This is kind of disappointing as this seems like it should be a pretty capable board. I can't figure out if there's some other setting in Marlin I'm missing that's causing the processor to be overwhelmed and skip steps. I'm using the stock Creality (Ender 3, CR-10) 12864 LCD and had to set one of the delays to 600 to remove artifacts, so I'm wondering if that's causing some of the slow down as I've seen some warnings about that. All in all, I'm going to be pretty disappointed if I can't use over 16 microsteps on this board.
Last reply by BIQU info, -
- 1 reply
- 196 views
Hello, I've got the octopus 1.1 which worked great with marlin on a spphire plus now it's on another printer , flashed klipper and all seems ok but I got bed power always on . Green led on bed ouput is on from power on(bed is heating,ssr is conected properly ). There is no visible dmg , evrey component works , bed power and output where not conected during flashing . is it broken?
Last reply by BIQU info, -
-
- 1 reply
- 280 views
How to disable the 120ohm resistor on the can bus of the Octopus Pro board?
Last reply by BIQU info, -
-
- 1 reply
- 189 views
Greetings- Does anyone have any experience installing a BTT 32-bit motherboard in a D6? It is a 24-volt machine, presently equipped with a very substandard, noisy, failure prone, mobo. Firstly, can anyone suggest a board-display combination that is as close to plug-and-play as possible. (Famous last words!) Within reason, I don't mind replacing minor components, like the thermo-resistor or, within reason, switching wires about. Thanks in advance. -Mark
Last reply by BIQU info, -
- 2 replies
- 168 views
I built the 3D printer and I put the tft35 motherboard but the print limits are 235 X 235 mm. how I can increase this limits? Anybody hel me?
Last reply by BIQU info, -
- 1 reply
- 226 views
Hey guys, I just bought the new SK3 to upgrade my Ender 3 old board. I'm looking for the Marlin 2.x configuration that matches this board + Ender 3 configuration, since this board was just release a few weeks ago, is there anybody that know where I can find a example in how to change the example configuration that come with the board in order to match Ender 3 required settings ? * I don't have any mods in my printer. Thanks!! Guto
Last reply by BIQU info, -
I just purchased a BIQU B1 SE PLUS printer - and I love it however after building the github Marlin source I noticed a problem. QUESTION: Does the firmware on my printer correspond to the github prebuilt firmware and marlin source code ? It seems to be that the firmware on my printer is more recent than the github version. And if I flash files in github that I would have older firmware BIQU B1-SE/PLUS 2.6.0 Aug 30 2021 17:26:25 versus BIQU B1-SE/PLUS 2.6.0 Jan 10 2022. Thank You helakejr DETAILS: 1) My B1 SE PLUS Printer says that the firmware version is: Board: BTT SKR 2 Firmware: BIQU B1-SE/PLUS 2.6.0 Jan 10 2022 NOTE: This disp…
Last reply by helakejr, -
-
- 2 replies
- 978 views
Hi! I purchased a B1 SE Plus yesterday from Micro Center, got it all assembled, attempted to start a print, but realized no material was extruding. I attempted to do all the steps to clear a blockage, even though there shouldn't have been one that quickly after getting it, but no matter what, the sample PLA was not reaching far enough to even begin to soften. Earlier today, I took off the nozzle to see if I could see anything and get a bit easier access to the blockage when a roughly 1 inch piece of the PTFE tubing just fell out with the nozzle. The blockage position corresponds to the end of the tubing that fell out, about 1 inch from the nozzle threading. There are no b…
Last reply by helakejr, -
-
- 3 replies
- 306 views
Tried to print attached stringing test. Much stringing. I'm using the standard B1 machine profile that has retraction distance at 7 mm. Does anyone know how to correct this situation? four_square_cons.stl
Last reply by helakejr, -
- 2 replies
- 242 views
Does the SKR2 board rev b have only one size of fuse for both sockets, or are they different sizes and if they are different sizes which one goes where? I've looked every where I can think of to find out, but none of the pics show the fuse sizes.
Last reply by Cryspy Arcani, -
- 1 reply
- 392 views
The problem I'm having is that the filament is extremely difficult to remove from the hot end. This has happened twice -- once with the sample filament, and now with the Inland PLA that I purchased at MicroCenter. Heating up the hot end doesn't help either. On both occasions, I have had to remove the PTFE tube from the hot end and used pliers to pull the filament free. Upon extraction, I measured the diameter of the filament, and at the very end, it's 2.02mm vs 1.78mm for the rest of the filament. I never had this problem with my Ender 3 Pro. This probably wouldn't be that big of a deal to me, except that it makes it impossible to take advantage of the filament runou…
Last reply by GPSevinsixx, -
- 4 replies
- 361 views
I recently purchased two Raspberry Pad 5 for Compute Module 4 in two seperate orders. I received one of them and tried to make it work, but i am facing network issue. I flashed mainsail OS to use Klipper for my Ender3 S1 Pro But my Pad5 is not able to get the correct IP Address from my router When I check the ip using ifconfig command it gives me something like this, 169.254.12.165 I tested exact same setup with my Raspberry pi 3B+, it worked fine. I tested the same the micro SD card and ethernet cable to both PAD5 and RPi3B+ PAD5 is always unable to get the correct ip address from my router can you help me out to solve this issue?
Last reply by BIQU info, -
- 1 reply
- 206 views
I have installed an SKR Mini E3 V3.0 with a BLTouch in my Ender 3. It took a while to get the BLTouch working, but it seems to be working as expected now. The problem I am now experiencing is when I print something, the BLTouch does it's calibration run and the print starts... I get the percentage of completion on the display, but after the first few (maybe 5 - 10) layers, the completion jumps to 100% and the print stops. I have tested with and without the TFT35 E3 V3.0.1 connected, and I get the same results. I have tried with several gcode files, and they all end the same. I cannot get anything to print past the first few layers. Any help you…
Last reply by BIQU info, -
I have spent hours trying to get an ender 3 Pro to print ON THE BED. Once the board is installed and you turn on the printer, what are the steps to follow, in what order to 1.manually level the bed, 2. to set the Z height offset, and 3. to set the probe offset? I have adjusted the z endstop switch so that the nozzle is just above the bed. When I next go to manually level the bed, the nozzle raises UP slightly and then moves into position to manually adjust the bed. If I were to RAISE the bed to meet the nozzle to level the bed, the nozzle will then crash into the bed when I go to home the printer. Also, I have set the Z height offset, and I have set the probe offset.…
Last reply by BIQU info,
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
- 0 replies
- 0 views
-
- 0 replies
- 23 views
-
- 1 reply
- 35 views
-
- 6 replies
- 3,033 views
-
- 0 replies
- 29 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
