Other Accessories

Followers 1

Start new topic

714 topics in this forum

Sort By

max31855 with SKR Mini e3 v3.0

September 30, 2022 by Floyd
1 reply

180 views
I'm trying to use the max31855 with the skr mini e3 v3.0 via the hardware spi interface. The breakout board is wired up, the only issue is getting marlin to build. When I try to build it I get the following error; Marlin\src\HAL\STM32\../../inc/SanityCheck.h:2365:4: error: #error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN." 2365 | #error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN." Thanks in advance. Floyd

Last reply by BIQU info, September 30, 2022
BTT SFS V1.0 Smart Filament Sensor Detection Stuck Blocking Filament Module

July 1, 2022 by cov_florin
1 reply

207 views
Hi, BTT SFS V1.0 Smart Filament Sensor Detection is compatible with Firmware: Klipper and BIGTREETECH BTT SKR 3 EZ Control Board?

Last reply by BIQU info, September 30, 2022
Biqu b1 not turning on.

July 7, 2022 by Brando eacobar
1 reply

165 views
Used the previous night no worries. Turned on the next day and the screen gave a light flash than all black.

Last reply by BIQU info, September 30, 2022
tela azul

July 21, 2022 by rafaeldias
1 reply

173 views
cliquei em desbloquear e mudei a interface e a tela ficou azul,oque devo fazer ?

Last reply by BIQU info, September 30, 2022
Biqu B1 SE Plus IDEX belt length

July 23, 2022 by Peteh59
1 reply

243 views
I am installing the IDEX upgrade on my B1 SE Plus. The belt is about 25-30mm too long. I can't tighten it enough even when I move the adjusters to the edge of the gantry - any farther, and only 1 nut holds it to the gantry. Is there a way to shorten the belt? Or get replacement? Or a different attachment to the print head that allows shortening of the belt?

Last reply by BIQU info, September 30, 2022
Problem while printing

August 1, 2022 by Mango Marketing Digital
1 reply

243 views
Hello im new in this 3d printing world and i need some help, i've printed some pieces but something strange started to happen, in some point of the printing the hotend just stuck in the bed and keeps pulling out PLA, yesterday i left it printing alone when i arrived it had a lot of pla inside the extruder, i had a lot of work to clean it up and unclog the hot end... so today i tried it again and it starts ok but at some point it happens again, ill show you guys some photos, i hope you guys can help me. this printer is new, im with it about 2 weeks now cura.log

Last reply by BIQU info, September 30, 2022
Miss

August 4, 2022 by Tsih
1 reply

197 views
Hi, I have a BIQU B1 which I am trying to use. I turn it on amd it says 'no printer attached' then comes up with 'failed to enable bed levelling, echo: bed levelling off, echo: fade height off' I dont have auto bed levelling?? Is anyone able to help get this up and running??

Last reply by BIQU info, September 30, 2022
BIQU BX 3D Printer

August 5, 2022 by NeatMachine
1 reply

264 views
Hello, I have a BIQU BX 3D printer and am using CURA and printing via USB, I am able to start prints, but the printer stops before the print is completed. I have set my computer to not go to "sleep" and I believe I have my CURA settings set appropriately. Can someone tell me what may be causing this problem and things to do and check to solve? Thanks much! Dave

Last reply by BIQU info, September 30, 2022
BIQU B1 will not turn on

August 6, 2022 by Clifw
1 reply

193 views
I just purchased a new BIQU B1 printer and spend 4 hours assembling it. When I turn it on, nothing happens. I have tried to install new firmware bot still will not turn on. I do not want to return it but unless I get some help in a day or two I will have to return it. Please help. clifw

Last reply by BIQU info, September 30, 2022
Manta M4B/CB1/2209s sensorless homing

September 28, 2022 by jeep.kevin
0 replies

116 views
Hello all, So far everything is working great. I have this installed in an Ender 3. I've tried entering the J15, J21, etc. as the diag pins in Klipper and it says these do not exist in the mcu. has anyone got sensorless homing to work, if so what did you put in the config file fr the diag pin values. thank in advance.

Last reply by jeep.kevin, September 28, 2022
HERMIT CRAB

September 28, 2022 by Emmanuel Malveiro
0 replies

179 views
Bonjour J’aimerai savoir si le Hermit Crab est compatible avec l Extrudeuse intelligente H2 avec capteur de filament intégré qui est sur une evo avec rail lineaire RCIMe

Last reply by Emmanuel Malveiro, September 28, 2022
(BIQU BX) how to set up the BLtouch you sell or somthing

September 26, 2022 by Emil Jørgensen
1 reply

183 views
how the fuck do i install thes BLtouch that i bouth on your site i have a mount and and probe offsets -35 +24 -0.78 offset but i dont know if it the firmware or whf ther is the problem i have the probe connectet to the hothed but is just lights red and keep staying up ? like is the doing the probing the wrong way also it is dropping the probe then taking it back into it self dont know is a ender v3.1 is that a fucking 5v probe or is it not or maby just fucking sell the standard thing you sell with buqu BX printer the one to auto bed level on you fucking store og give me a amazon link so i know whf to buy

Last reply by BIQU info, September 28, 2022
EBB36/42 Can Bus Operating Temperature Range

August 1, 2022 by Heath
1 reply

465 views
I can't seem to find the Operation Temperature Range for this board in manual. Could someone point me in the right direction? Thanks.

Last reply by BIQU info, September 28, 2022
BTT DCDC Mode Power Module (SKR 3)

July 14, 2022 by Tendeiro
1 reply

447 views
Hi! So, I just purchased a SKR 3 EZ and Biqu H2 Smart Extruder to make something new out of my Anycubic Mega X. I intend to keep Klipper as the firmware (with a RPi 4) I've purchased as well the DCDC Mode, and here's where my questions begin: - I read somewhere that it would power the RPi 4 without any issues. What does exactly that power module do? I mean, I know it stabilizes 5v (in this case)... but where? I have 24v fans connected to FAN0 and FAN1. - How do I connect the RPi directly to SKR 3? Through TFT pins, even for power? In that case, does the DCDC Mode do anything? I feel that there is little to almost no information regarding the …

Last reply by BIQU info, September 28, 2022
Hermit Crab, linear rail and belts

August 8, 2022 by rmd
1 reply

268 views
Hello. Before buying a hermit crab tool changer i'd like to know how is the fixed plate attached to the bearing block, and how can i attach the belts to it. I could not find information on BQ site nor internet. My printer is a custom coreXY, with XY linear rails and triple Z axis Thank you

Last reply by BIQU info, September 28, 2022
Powering EBB42

August 16, 2022 by Flackenstein
1 reply

375 views
I am in the process of converting over a printer to klipper using an Octopus Pro, Pi 4+, and EBB42. I was going to wire power for the EBB42 via a fused power block off of the 24vdc switched power module, but was curious if we could repurpose the HE ports on the Octopus Pro main board to supply power. Does anyone know if we can do this via klipper config and if there are any cons to trying this? Thanks, Warren.

Last reply by BIQU info, September 28, 2022
Can't Find Wiring Diagram for Hermit Crab CAN Tool Plate or Fixed Plate

September 10, 2022 by wunderken
1 reply

176 views
I am wiring up my BIQU Hermit Crab tool plate, but I can't find a wiring diagram. There are connections for HE +/- (OK, hotend), CNC-F +/- and FAN +/- (which is the cooling fan and which is the heatsink fan)? Then there is NTC +/- (? Temp probe, maybe?). Anyway, I can't find a diagram that clearly lays this out. Has anyone found such a diagram? I love the products from BTT/BIQU, but as always, the supporting literature is either spread out or nonexistent. Any help is welcome. Thanks.

Last reply by BIQU info, September 28, 2022
Using the TMC2209-V1.2 manually

September 20, 2022 by chrisgray
1 reply

121 views
Hi, I want to connect a TMC2209-V1.2 to drive a stepper motor manually, no 3D printer or motherboard. I looked through the IC manufacturer's datasheet for UART control and decided to go with Step mode instead. Please can someone tell me: Are current limit resistors required externally and if so, how do I connect them? Are the internal current limit resistors in use by default, and what do I need to do to configure them if not? Can the logic supply be 3.3 VDC? Do I need supply decoupling capacitors?

Last reply by BIQU info, September 28, 2022
Pi TFT50 v3 as primary display

July 29, 2022 by cyclejockey
1 reply

159 views
I have an Ender 3 v2. I'm interested in purchasing an SKR mini e3 v3.0 board for it. As far as I know, the board does not currently support the E3v2 display. So, I'm also interested in a BTT display. My question is, can the Pi TFT display be connected to the BTT motherboard or can I purchase a RPi and use it and the Pi display as my primary (and only) screen if I'm using Octoprint or Repetier Server? I'd rather not have two different screens if it isn't necessary.

Last reply by BIQU info, September 27, 2022
Raspberry Pad 5 - No USB

August 2, 2022 by Jay McDonald
2 replies

206 views
Final got a CM4 ( 2GB Lite version - no eMMC) for my Pad 5. Install and after nmessing about I got teh display to work ( could never get the HDMI port to properly work) . Now I cannot get the USB ports to work. I have enabled them with the overlay line in config.txt to no avail. Not sure what to do with the line "otg_mode=1" that is in the Bullseye config file by default. All the manual seems directed at the eMMC version - I am booting from SD card on a lite version. Anyone have a working config.txt file or provide some guidance on getting USB to work. Does it matter if I am powering the Pad 5 through the USB C port or ? Jay

Last reply by BIQU info, September 27, 2022
Any update on the CB2 for Raspberry Pad 5?

August 18, 2022 by Jay McDonald
1 reply

460 views
any update on when the CB2 will be available? Can't seem to get a working CM4 anywhere. My understandng is that this will work with the RBPad 5 as an alternative to cm4. Is that correct?

Last reply by BIQU info, September 27, 2022
Connecting BTT TFT35-E3 3.0 to MKS Base v1.6

July 18, 2022 by Seafreak62
2 replies

233 views
All, I am attempting to connect my screen to my MKS Base v1.6 board. After startup it will show the BTT logo and continuous makes a long beep noise. It shows the option to go to Marlin or Touch but neither touch or the control knob functions. I am connected as below. EXP1 -> EXP1 EXP2 -> EXP2 RS232 -> AUX1 - The ^ on the plug is aligned to pin 1 on AUX1. The reset cable is not plugged in. Respectfully, Mr. Weber

Last reply by BIQU info, September 27, 2022
Raspberry Pi Pad 5 - Fan Connection

September 4, 2022 by pi_fan
1 reply

153 views
I am interested in attaching a fan to the CM4 on the raspberry pi pad 5. Are there any recommendations on how to do this? Thanks!

Last reply by BIQU info, September 27, 2022
Manta M8p + CB1 + BIGTREETECH PI TFT43 DIP V1.0

September 7, 2022 by Molgo
1 reply

237 views
I can't find the config needed to run PI TFT43 DIP V1.0 on the CB1 board I managed to do it with a raspberry pi 3. I have a manta M8P card or I plugged the CB1 card, I use a 40-pin cable to connect the CB1 card and the TFT (the cable works because I tested on a pi3) someone has already managed to market BIGTREETECH PI TFT43 DIP V1.0 on a CB1?

Last reply by BIQU info, September 27, 2022
Pi 3B will not power on with TFT50 v2 connected

September 14, 2022 by eman13
2 replies

130 views
I have a Raspberry Pi 3B with OctoPi up and running with no issue. it is using a 2.5A canakit power supply. I purchased a PI TFT50 v2.0 screen and when the screen is connected to the Pi, it won't power, the Pi won't power on. If I disconnect the ribbon cable for the screen from the Pi, it will power on. I have tested this with no other accessories connected. No camera and not connected to the printer, just the Pi and the screen. Could this be a power issue? Do I need more power than the 2.5A power supply will provide? If so, what should I get?

Last reply by BIQU info, September 27, 2022