BIGTREETECH Motherboards
99 topics in this forum
-
- 1 reply
- 98 views
Is it possible to use the i/o pins? I want to turn a pin on and off through gcode.
Last reply by devilking1584, -
- 1 follower
- 0 replies
- 108 views
My Tarantula Gen 1 printer prints great, I put a lot of upgrade and tuning into it. I would like to replace the original Ramps V1.4 board with a bigtreetech 32bit board. 1 I was told in doing so I would have to replace the thermistor in the heatbed with a compatible thermistor. I have the 220x280 large heat bed and know they are not readily available anymore and would have to rip the insulation to replace the thermistor. Is that necessary or can the bigtreetech board be programmed for the existing thermistor. 2 I know the LCD screen would need to be replaced, what would be an easy screen to get to work with the bigtreetech board. 3 Is there anything else I …
Last reply by A. J. Nemeth, -
-
- 2 followers
- 18 replies
- 2.9k views
Can somebody please explain how you would go about using the EBB36/42 with the Manta M8P/CB1 combination? Do you have to use a U2C board? Can you use a 3rd party Pi can bus hat from the CB1 GPIO pins on the Manta? I have read everything I can find and the information I have found is ambiguous at best. They went to a lot of trouble to package the Pi/CB1 with the board. It would be a shame if you had to attach a U2C with a USB cable, power, and the can bus wires.....seems sloppy!? I think they may have missed a trick by not build the can bus into the board to easily support their existing products.
Last reply by AllThings3DPrinted, -
-
- 1 follower
- 2 replies
- 181 views
I did the mistake I thought I'd never do and burned the board in the process. Now I can't connect to it anymore and I doubt it but is there a way to save this board? I don't know if MCU got burned too. I was using Klipper at the time so the reverse insertion protection didn't work I believe.
Last reply by Kaan Kasım, -
- 1 reply
- 152 views
I am installing a Pico in an Ender 5 Pro. I have OctoPrint running, and according to Kiauh both Klipper and Octoprint are installed. The flash step seemed to fail, fairly late in the sequence, and so no /tmp/printer is created. It seems like this is a way to determine if flashing worked, maybe? As far as I can tell, the firmware on the Pico is installed: BTT's Github directions say "the computer will re-identify the USB flash drive, means the firmware update is complete", which did not happen, but it did change the filename, which is what I've seen in prior efforts. [As an aside, these kinds of sloppy directions are really excruciating for someone who has never succe…
Last reply by Keith Winston, -
- 0 replies
- 106 views
I have the CB1 and corresponding carrier board Pi4B. On the back of the Pi4B board there is a DSI connector. What MIPI DSI displays are compatible? Here is the link to the CB1 and Pi4B combo I bought: https://a.co/d/1vLE555
Last reply by JimJam, -
- 2 replies
- 147 views
I just installed the SKR Mini E3 V3.0 with matching TFT35 V3.0 display screen and when I turn on the printer the display reads "No Printer Attached". I tried to use the appropriate pre-compiled bin file to update the main board. However the board does not respond to the firmware. Is it possible that I have a wiring issue? All help will be greatly appreciated.
Last reply by GhostRider, -
- 0 replies
- 74 views
I have a OCTOPUS PRO V1.0 populated with 4 TMC5160 Using Marlin 2.1.2 From Day1 Stepper worked , But I got the TMC CONNECTION ERROR , on the LCD And the RECV: Testing X connection... Error: All HIGH RECV: Testing Y connection... Error: All HIGH RECV: Testing Z connection... Error: All HIGH RECV: Testing E connection... Error: All HIGH From the M122 commands Since the Stepper still worked (motor moving) The TMC init is fine so, The CPU connection to the TMC MOSI+CS+CLK are working fine But the data back to the CPU (MISO) is not making it Poking around with my oscilscope , I found out the MISO signal is fine up to the …
Last reply by Tijeff, -
- 0 replies
- 104 views
Le he puesto un extrusor titan aero. Tengo que reposicionar la boquilla e invertir la rotación de la extrusora. Estos parámetros se han puesto en el archivo correspondiente pero al intentar compilarlo da error con script python. No se ha tocado nada más solo lo que he dicho. Muchas gracias.
Last reply by PuntaLanza, -
- 1 reply
- 107 views
Hey everyone. Hopefully someone can help me out. I am using the Manta M8P with the cb1 and I’m trying to set up the klipper printer.cfg file so I can use the Biqu H2 500c. This is a fresh build so I am building my file as I go. I am unable to configure the max31865 driver properly. I keep get an spi error. Can anyone point me in the correct direction or share their config file with me if they have this set up? Thank you in advance. Your name always comes up Tony so maybe you can help? @BTT Tony
Last reply by kishmj, -
- 0 replies
- 88 views
I have just installed a SKR 3 EZ in my Ender 3 pro. I want to just use the stock interface with it but cant get it working. it lights up but that is all. I have bought 3 different BTT TFT screens but also cant seem to figure out how they are supposed to hook up or if they would support Marlin so i sent them back. Like I said I would prefer to use the stock 12864. I think I should have bought the E3ez, instead. The CB1 and the flexibility of the board and the ability to just snap in the CB1 is pretty sweet. I think the hdmi/Pi TFT screens are also more suited to that board not to mention is was a simple plug and play from the standpoint of fit. I have a raspberry…
Last reply by A1bucker, -
- 0 replies
- 100 views
I've just fitted an SKR mini E3 v3.0 to my Ender 3 V2. Firmware loaded to the card fine, set up my CB1 and Klipper. Tried to increase the temp on the Extruder and the board would crash. Now the 24v to the Extruder is constantly on, even without Klipper connected or a print running.
Last reply by vintage juicy, -
- 1 reply
- 107 views
I bought the bigtreetech mini e3 v3.o and i cant figure how out to put the prper firmewre on it
Last reply by GhostRider, -
- 1 follower
- 0 replies
- 80 views
I have been messing with this thing for 2 months trying to get it to work and i am at my wits end so here goes. I have a Creality ender 3 pro, board got fried so i purchased a new one only to find, no display on power up. So i Bought a new display and still have no active display after installation. parts that i upgraded to are listed below. BIGTREETECH SKR MINI E3 V3.0 32 Bit Control Board for Ender 3/Ender 3 Pro/Ender 5/Ender 5 plus/CR-10 BIGTREETECH MINI12864 V1.0 LCD Screen VORON 2.4 RGB backlight mini Display Supports Marlin DIY For SKR 3D Printer Part Creality Sprite Direct Drive Extruder Pro Official Creality Ender 3 Dual Z-axis Upgrade Kit …
Last reply by Neil Nohacs, -
- 2 replies
- 123 views
Having issues where an inductive probe will not work when connected to the inductive probe port on an Manta M8P Seems to not be getting power.
Last reply by Baz_Snow, -
- 0 replies
- 81 views
/** from Config-adv-h file * Thermocouple Options — for MAX6675 (-2), MAX31855 (-3), and MAX31865 (-5). */ //#define TEMP_SENSOR_FORCE_HW_SPI // Ignore SCK/MOSI/MISO pins; use CS and the default SPI bus. //#define MAX31865_SENSOR_WIRES_0 2 // (2-4) Number of wires for the probe connected to a MAX31865 board. //#define MAX31865_SENSOR_WIRES_1 2 #define MAX31865_SENSOR_WIRES_2 2 //#define MAX31865_50HZ_FILTER // Use a 50Hz filter instead of the default 60Hz. //#define MAX31865_USE_READ_ERROR_DETECTION // Treat value spikes (20°C delta in under 1s) as read errors. …
Last reply by BigO, -
- 0 replies
- 62 views
I have had 3 Octopus boards fail in a row. They worked for awhile, and then die. The blinking led stops and no blue light. Just before they die, they displayed 4 green leds near the hotend power block. I am using Btt TMC2209 drivers. They have been swapped from one board to the other. Could a bad driver cause this?
Last reply by Wayja2106, -
- 0 replies
- 42 views
Running Klipper. My idea is to put a SSR tied to an output pin for auto power off. If I do this, how long would I have to hold on the SSR before the Octopus takes over?
Last reply by Keshka Kotera, -
- 1 follower
- 1 reply
- 87 views
I recently purchased a Manta M4p and CB1, and despite installing all the firmware and ensuring that Klipper is functioning, the printer will only boot up when the USB jumper is attached. When attempting to power it via the power supply, the printer fails to boot and only lights up. I have tried various troubleshooting techniques but to no avail. I have attached a picture of the board and its power lights for your reference. Unfortunately, my attempts to seek support from the manufacturer have been fruitless, as they have been unresponsive for the past 18 days and replied with the number 1 before closing my case. As such, I am turning to the community for assistance. It is…
Last reply by rhawley88, -
- 0 replies
- 32 views
I need help with the firmware I think. I can't get it to auto home correctly.
Last reply by PrinceRoxasXIII, -
- 3 replies
- 64 views
My board arrived about 8 days ago.I configured Marlin and it was running great.But now when starting the SKR 1.4 board, the error message appears: E1: MAX TEMPERATURE please Restart. Can someone help me?
Last reply by koehlr, -
- 0 replies
- 67 views
Hello dear printing community, by today i started the exchange from my SKR1.4Turbo to the new E3EZ Board (For CAN and other features). It went all well in physical terms, all modules and plugs fit nicely, also the automatic shutdown relay already works again (great). But, when it comes to installing the CB1 (in terms of software) i do get interrupted at the step to login via SSH to the CB1/Manta Board. No matter what i do, the ethernet connection (do not use wifi, lost the fiddly antenna) doesnt work. No lights show up at the port, i can´t see it connected to the router.. I tried different cables, Routers, re-flashed the image with raspbi imager and also…
Last reply by Ivo, -
- 0 replies
- 23 views
Hi, I'm trying to run SKR mini e3 v2.0 with a BTT Mini12864 display on an Ender 3 Pro, and not being really successful, the hardware seems to be working, but the display does not show anything when booting. Maybe, I'm running the wrong firmware? Thanks in advance.
Last reply by Jey, -
- 0 replies
- 14 views
I have a Creality CR10-V3, and I need a new motherboard. I'm looking for a MB that will fit the CR10 case, I don't want to carve any new holes. Can you help me by suggesting one of your products?
Last reply by hankthompson, -
- 3 replies
- 27 views
Hi i have just received the bigtreetech Tango V 1.0 mother board Its is replace a bad board on a brand new Reprap 3 in 1 out printer HE3 d model Ok most of the wiring is clear but it came with a plastic bag with what i understand as called jumper caps x 5 of them.. Can anyone enlighten me of what they do and where they go on the board as several pin options are there...Cheers Phillip
Last reply by phillipgcollis,
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
- 0 replies
- 0 views
-
- 7 replies
- 83 views
-
- 0 replies
- 2 views
-
- 0 replies
- 14 views
-
- 0 replies
- 13 views
-
Announcements
-
Online Store
If you have any issues with the product, please submit a support ticket.
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
