BIGTREETECH Motherboards
240 topics in this forum
-
- 1 reply
- 382 views
Hi. I've installed a SKR3 EZ board with EZ2209 drivers to my standard BIQU B1 printer (no BL Touch, only 1 Z-axis). I am trying to run the machine using a standard Marlin 2.1.x. I took over the parameters for config.h from the standard BIQU B1 repository for Marlin 2.0.x Right now I am struggling with the axis homing. When I push the 'home' button the motors drive approx. 15mm in '+' direction and then stops. Same behaviour for x, y and z axis.
Last reply by ElBernado, -
-
- 3 replies
- 428 views
I have a BTT_SKR_3 and the TFT35 screen. For the last several days I have been trying to get the proper firmware compiled. I have tried several versions of Marlin. With most of them I can get the software to compile just fine until I try to enable the function for the TFT display. Then I get an error that says the TFT-SPI display only works with the STM32F series chips. Does anyone know a way to get around this problem. Thanks for any help you can give.
Last reply by biquser1024, -
-
Hello, I need some help please. I have upgraded my tool head from an Afterburner to a Stealthburner and added a sb2209 tool head can-bus board. My current mainboard is an Octopus 1.1 which was running great before the upgrade. Devices: BTT Octopus 1.1 RaspPi 4B SB2209 can-bus tool head board. Connections: Pi (usb-a) to Octopus (usb-c) Octopus (usb-a) to Pi (usb-c) for power. Octopus (rj11) to sb2209 tool board, and 24v power supply to sb2209 tool head board. Firmware loaded: CanBoot for Octopus flashed with STM32cube menuconfig below CanBoot for SB2209 flashed with STM32cube menuconfig below: …
Last reply by SeanR, -
- 0 replies
- 333 views
Hi i need the Boodloader for an SKR3 With STM32H723 !!! I have tried to get the CAN bus to work unfortunately I have somehow broken the Boodloader !
Last reply by Peter-Koppi, -
- 0 replies
- 372 views
Hello, I am trying to connect MicroProbeV2.0 to Octopus Pro. The instructions only mentioned Octopus (446/407). Since the pinsign is the same, should I use the same settings? The firmware is using Marlin.
Last reply by 渥美元康, -
- 0 replies
- 436 views
Hello, I bought a brand new SKR 1.4 a few days ago and have configured it with the latest Marlin 2.1.2.1. before I could start connecting the 3d printer parts , I decided to test the heat bed and extruder powers. Without anything connected when I turn on the Heat bed via Octorprint or Pronterface I get the error printer halted and disconnects. I tried to use a multimeter to check the power. The Extruder power works fine but the Heat bed does not give out any power. Any thoughts on what could be causing this ? Is there something I need to configure in Marlin specific to SKR 1.4 for the heatbed ? I have tried looking at configuration.h online from other folks but can…
Last reply by Kenny Smirth, -
- 1 follower
- 2 replies
- 398 views
Hello, I got given a CR-10 MAX, but the SD reader has stopped working amongst other things. I could just go get a new mobo (controller) for it, but if I could upgrade it now instead? I live in South Africa and the power is not always on for 3D printing timeframes.. Now I know the CR-10 MAX has its own special connectors, but I'm not worried about that - I'll handle that myself and make a new case (box) if I have to. The only problem I have is that I'm pretty new to this world of 3D DIY and I'm not sure what's compatible with boards and the modules, etc. I would also like to run Klipper instead of Marlin. So here is my list: SKR 3 EZ + 5PCS EZ2209 BTT …
Last reply by Malcolm Lunt, -
- 0 replies
- 246 views
Can anyone help? Im a newb to all the code side of life. My e3v2 board failed so took the plunge into manta/klipper. Has anyone got an in depth guide how to setup for an e3v2. I've had friends help me by printing my mounts for m4p as i only have one printer that I want to bring back to life. It's stock e3v2 other than sprite pro dd extruder and linear x axis. Any guide be appreciated Thanks Danny
Last reply by Gibbo, -
- 0 replies
- 267 views
Hi all, I just installed a new Manta E3EZ in my Ender 3 Pro. Everything seems to be fine EXCEPT all axis movement is 2X too large (when commanded to move 10mm, the axis moves 20mm). I'm using the Klipper config from the BT site. Relevant config enclosed (ignore the parts of the file that specify bed mesh - it was created before I discovered the movement issue) I've submitted a ticket to BT but haven't received a response. Anyone else seen this? Thanks. printer.cfg printer-ender3.cfg
Last reply by CBZ, -
- 0 replies
- 373 views
Hi I have searched and trawled but I cannot seem to find an answer. I have 2qty nozzle fans @ 0.84W ea 12VDC and 3qty workpiece cooling fans @ 1.56W ea 12VDC I wish to run the nozzle fans from FAN0 and the workpiece fans from FAN1 both with PWM Is this possible? Can the FAN terminals take 4.68w for a single outlet? What is the maximum power available over all 3 terminals? My power in is 24VDC Thank you for your help
Last reply by OldManRiver, -
- 0 replies
- 278 views
hello everyone not that long ago, I bought a btt manta m4p motherboard with a btt cb1 but one day the screen that I bought started to smoke and also since that day my cb1 does not doesn't work anymore, I would like some help because I don't understand it anymore good to you Lucien Nowak
Last reply by Lucien Nowak, -
- 0 replies
- 376 views
Hi i have a new Manta M8P and CB1, I can get the X motor to move and home. it's a bigtreetech s42c Closed Loop motor. But i can't get the Y motor ( bigtreetech s42c Closed Loop motor) to move. If i put the y conector in the x driver it will move so it's not the driver or motor. I have looked at the printer.cfg over and over even tried moving Motor2, [stepper_y] on to Motor 5 and setting up the printer.cfg but still not working. all the jumpers or on VBB for power i did try HV as well. i have attached the printer.cfg Thanks Paul generic-bigtreetech-manta-m8p-V1_1.cfg
Last reply by paul eley, -
- 0 replies
- 337 views
i need the firmware for skr3 mini v3 for ender 5 plus
Last reply by The Gamerboy, -
- 0 replies
- 521 views
I have a octopus v1.1 board instaled in my 3d printer and want to upgrade the x/y stepper drivers from tmc2209 to tmc5160T pro. I think i have setup the config for the drivers correctly. [tmc5160 stepper_x] cs_pin: PC4 spi_software_sclk_pin: PA5 spi_software_mosi_pin: PA7 spi_software_miso_pin: PA6 run_current: 1.6 interpolate: False stealthchop_threshold: 0 [tmc5160 stepper_y] cs_pin: PD11 spi_software_sclk_pin: PA5 spi_software_mosi_pin: PA7 spi_software_miso_pin: PA6 run_current: 1.6 interpolate: False stealthchop_threshold: 0 My Z drivers are also tmc2209, when I run a G28 command to home all axes, the bed moves…
Last reply by Max N., -
- 0 replies
- 470 views
When I home z it will travel half way up and just stop. https://drive.google.com/drive/u/0/mobile/folders/1_L9qzqSwnYzQmVa-WLgxbIq9VYuWYGxh?usp=drive_link&pli=1 In there is my configuration files and a short video of what's happening. Been stuck on this for weeks.
Last reply by Djripper666, -
- 0 replies
- 305 views
I bought an Ender 3 V2 3D printer, and it came with several upgrades, including the E3 RRF board upgrade. However, since it's a second-hand printer, I've encountered several issues. Unfortunately, it did not come with a touchscreen. I've managed to address all the problems except for the extruder. There appears to be no power reaching the motor from the motherboard, and I've checked all the cabling. I'm unable to identify the root of the problem. I've also tested the motor, and it is functional.
Last reply by charlie, -
- 0 replies
- 322 views
Hi looing for advice on an upgraded mainboard for my Ender 3 V2 after issues were the board got fried when thermistor shorted and now wont boot Im looking at the BIGTREETECH Manta E3EZ V1.0 For Ender 3 but want to know what parts i need to order to make the complete swap from the v4.2.2 board i currently have 1.BIGTREETECH Manta E3EZ V1.0 For Ender 3 2. 5PCS EZ2209 3. CB1 If anyone can help me make sure I get all the right parts to upgrade the Ender 3 v2 mainboard to a Manta E3EZ Or is there anything better I've looked at the BIGTREETECH SKR MINI E3 V3.0 but looking for something that has Wi-Fi and Networking features as well as possibility to add upgra…
Last reply by SussexPerformancePrint, -
- 0 replies
- 455 views
i am using SKR PRO V1.2 with MKS H43 but there is only MKS LOGO and it is not going foreword please help me out !!
Last reply by Taaran Rai, -
- 0 replies
- 291 views
Hallo ich habe ein Problem das er keine Verbindung findet unter Putty und dem befehl: python3 flash_can.py -i can0 -q Woran kann das liegen? Jumper sind drinnen
Last reply by sascha, -
- 0 replies
- 291 views
I have an Ender 3 Pro with a BTT SKR Mini E3 V3.0 and TFT upgrade set. My issue is that at idle, my hot end fan and power supply fans run at 100%. But as soon as there is any power draw from heating the hot end or the bed all of the fans drop down to 25% (even if I set the nozzle fan to 100% it is affected as well). Also the power available to my hot end drops from 24v to 18.6v at during this issue with the fans (which in turn, make heat up very slow). I keep getting thermal run away errors or thermal kill errors at random times once the hot end gets above 190c which I assume is caused by the hot end fan running at 25% of what it should be. Any idea where I should st…
Last reply by Ezeekial, -
- 0 replies
- 248 views
hi, I hope someone can help me. the original control board on my printer burnt out so decided to upgrade it to a btt skr 1.4 turbo but have written the firmware 3 times now and keep having problems, the first 2 time i had 72 errors when trying to compile it, and the last time I managed to compile it but can't get the bed leveling working and give up. I don't suppose someone has already done this and I can pinch a copy of there firmware, my setup is. btt skr 1.4 turbo btt tft 24 v1.1 btt tmc2209 btt rrf wifi v1.0 BlTouch any help would be greatly appreciated.
Last reply by Ian Reddish, -
- 0 replies
- 183 views
Hi I have problem with my skr 1.4 turbo when I start printer it show that my bad is heated for about 125 °C. When I try disconnect heating sensor nothing change. It still show 125 °C. I will be happy if anyone know what it can be.
Last reply by Falc0N, -
- 0 replies
- 327 views
Let me start by saying i am still learning so please be patient with my ignorance. I have an Ender 3 pro that i had upgraded to the skr e3 mini v2 and used to print decently.. i upgraded to a biqu h2 v2s and added a bl touch at the same time...i have tried to compile the firmware and at this point it will heat up and load the filament but if i try to print it heats the bed and nozzle and just squirts a little filament and then says it is complete. Please any help as to why it wont print anything. any pointers thanks in advance
Last reply by Chris Pacheco, -
-
- 1 reply
- 290 views
I just recently received the SKR mini from your store but with a different chipset than advertised(STM32G0B1RE) please see photographs(STM32G0B0RE). I have therefore got difficulties compiling and flushing the firmware as the board is stock on the process and a red light is flashing permanently. I have tried to flush the firmware directly via USB and using ST card. Please advise urgently
Last reply by Coco-BQ Team, -
-
-
- 3 replies
- 384 views
Is there any technical product page for SKR V1.4 Turbo ? I can't find any. Any specific pin setting for 24V? How to set i.e. pin 0.16 HIGH with M42? P16? Any smoothieware starter cinfig.txt with TMC2209?
Last reply by Coco-BQ Team, -
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
- 0 replies
- 7 views
-
- 0 replies
- 3 views
-
- 1 reply
- 1,402 views
-
- 1 reply
- 228 views
-
- 1 reply
- 159 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
