General Discussion
122 topics in this forum
-
- 1 follower
- 3 replies
- 479 views
Hi Pad 7 arrived yesterday but I cannot remove the sd card. It will not push in and spring back ( normal) and it won't slide out. Any help appreciated.
Last reply by MrAnderson, -
- 0 replies
- 111 views
help with wiring my ender 3 pro to the Manta m8p v1.1 mainboard with CB1
Last reply by hyspead, -
- 0 replies
- 122 views
Helloo everyone I am writing today in an emergency situation. I am a user of your TFT35 LCD controller, and recently, while I was adding a filament sensor to my printer, there was a bad short circuit in the printer controller. This short circuit also fried the TFT35 microcontroller. Unfortunately, the GD32F205VET6 microcontroller that is used in the TFT35 LCD is not available in my country (Iran). I have been searching for a replacement microcontroller, and I have found that the STM32F407VGT6 microcontroller is a compatible alternative. I am writing to you today to ask if it is possible to use the STM32F407VGT6 microcontroller in the TFT35 LCD controller. I am in u…
Last reply by Rezabargi, -
- 0 replies
- 161 views
Has anyone try painting with 3D printing on HueForge? I hear that this software can convert 2D photos into 3D printing files, and can add filters, adjust colors, enhance image details, and customize options, making the printed photos more artistic. I have seen many beautiful works on Reddit. It really bringing infinite creative imagination to many different types of projects.
Last reply by Sabine, -
- 0 replies
- 167 views
Hi, I just got a biqu b1 se plus. When seeking home or auto leveling the nozzle touches the bed and keeps trying to go down past the bed. Any ideas why, do I need to do a firmware update? Thanks
Last reply by dabby80, -
- 1 follower
- 0 replies
- 108 views
I have several items purchased on the official BIQU website, unfortunately they will not be useful in my printer improvement project, I would like to return them and I am ready to pay for shipping to China. I will also add that these items have not been horribly used or even opened. I have also read your company's returns policy. I contacted the support by e-mail about this, but unfortunately I only got one reply to the e-mail. when I tried to find out what steps I had to take - no one wrote back. why is it so hard to get information on this. please, help me.
Last reply by JakubB, -
- 0 replies
- 110 views
Hey fellow 3d printing hobbyists 😁 I've been looking to upgrade my Ender 3 v2 for some time, and after looking here and there, I stopped on BTT products which seem to be highly regarded. I selected a few things and wanted some help on figuring out if it's appropriate to buy them : - Control Board : SKR 3 EZ - Drivers : EZ2209 - ADXL345 Accelerometer : Not sure I would buy the BTT one yet since my printer is cartesian style, and BTT's one seems to be more adapted to CoreXY printers with the 36 motor mount - BTT Relay V1.2 Automatic Shutdown Module After Printing -Screen : I selected a TFT35 SPI + BTT Pi V1.2 but that's where I'm kind of lost. T…
Last reply by Frédéric Manseau, -
- 0 replies
- 103 views
My 2209 driver went out and all I have on hand are MKS 2225 drivers. Will these work on my board?
Last reply by Robert Blot, -
- 0 replies
- 293 views
Is it worth it to upgrade from a SKR Mini E3 V2 to V3? What does going to V3 give you over what a V2 has? Has the user experience with V3 been good?
Last reply by Arogen, -
-
- 3 replies
- 1k views
Has anyone else happen to have this exact combination of components? I'm having a little issue with getting my printer nozzle to heat up after installing the Sprite Pro on my ender 3 Pro, while using a BTT SKR Mini E3 32 bit board, and I'd also like to know if anyone could help me make sure I have the correct 5 pin connector harness connected to the Board. The Creality Sprite Pro comes with a CR Touch 5 Pin conector, but so does the Creality CR Touch, so my question is which wire connector do I use the One that comes with my Sprite or the one that comes with the CR Touch? I currently have the connector that came with the CR Touch plugged into the 5 Pin Connector. Is this …
Last reply by Bhlhomme, -
-
- 0 replies
- 94 views
I don't see live support anymore on their site, just the coin icon. I wanted to inquire about my open ticket for a new micro probe for my hurakan, that the new probe was suppose to be out by the end of June.
Last reply by gv71, -
- 0 replies
- 115 views
I am making an RC car, and I want to 3D print the tires. Which 3D printer filament do you recommend? I prefer TPU filament, as it is flexible and impact-resistant.
Last reply by Ankers, -
- 1 reply
- 782 views
hi guys, so im having issues installing a sprite extruder from creality onto the BTT SKR mini V3 i had everything wired up correctly however when i turn on the printer, the bed and the hot end immediately begin to heat up. thats WITHOUT turning the temps up on the screen menus. they just turn on and heat up. also none of the fans are working. i soldered a connector onto the fan + - for the board connector and tested it via a bench top power supply set to 24v as the printers are 24 volts. that was the only modification made to any of the wiring. the firmware was configured for an ender 3 pro with creality CR touch and power loss detection disabled. it…
Last reply by secretreeve, -
-
- 2 followers
- 7 replies
- 230 views
Hello all, I would like to open a ticket at BiQu. On the page "https://bigtree-tech.com/de/pages/submit-a-ticket?" I can enter my email address, but I don't get a message. After some time the page is reloaded and it just says the same thing. I did not get an email to verify my email address either. Does anyone also have this problem or can help me? Greeting, Daniel
Last reply by BigVirgil, -
-
- 0 replies
- 110 views
hello! I'm starting my career on 3D printing and I got a little problem, my printer is not measuring the temperature correctly, it is constantly at 85 degrees, I have a Biqu-b1 it started when I changed the nozzle and the hotend twisted a little, after I put it back in place it was fixed at 85°C and even if the whole head is disconnected, it is always 85°C and it is not possible to heat it up, because it appears " printer halted, kill called" Does someone know what's the problem and how to fix it please?
Last reply by João Pedro, -
- 0 replies
- 206 views
I ask my friends and the Chatgpt, and they all think the filament dryer is a necessary 3d printing tool. I think the two advantages are important for us: 1. Improves print quality： Drying filament before printing can help achieve better print quality by allowing the filament to flow more consistently through the hotend. This can result in smoother surface finishes, crisper details, and more dimensionally accurate parts. 2. Allows storage of opened filament. Once a spool of filament has been opened, it will start to absorb moisture from the air which can degrade the material over time. A filament dryer allows filament to be dried and stored for extended periods while …
Last reply by Ankers, -
-
- 2 replies
- 1.3k views
I'm looking at getting a BIQU B1 Plus but I don't see the Printer on Cura. Is there a way to add it or is there a printer profile that matches?
Last reply by woahcheeto, -
-
- 0 replies
- 227 views
wanting to use the skr min e3 v3 from my ender and use with my laser cnc is this all possible if so can i have someone's imput thank you for any and all support
Last reply by noyesj, -
Hi all, I upgraded to the latest 'nightly' Marlin build for my B1 and the latest firmware for the TFT. Now, my hotend LEDs don't function properly. 1. White is white 2. Blue is right-side blue, left-side white 3. Green is right-side green, left-side amber ??? 4. Red is right-side red, left-side white The on/off buttons on the TFT do nothing either. I've looked at the BIQU source firmware config.h and made mine match. The only difference was my said 2 LEDs and BIQU's said 4. Nothing seems to matter. What in the world is going on?? lol Thanks for any insight! Thowci
Last reply by Novy 01, -
- 0 replies
- 176 views
Newbie: Ender 5 Pro, BTT SKR mini E3V3; TFT35 E3; BLT Prints start well, but after a minutes, there is lots of clicking from the extruder and retracts are very large set to 1mm, probably moving >10. Soon I find it printing in mid-air without filament coming out the nozzle. I've tried running higher temps, and replaced several nozzles. Filament spool is free moving. And I don't think there is a clogged nozzle. Any thoughts? Edward
Last reply by Edward K, -
- 0 replies
- 109 views
I have a BTT Skr 2 bd. I have a BLTouch attached to the servo and probe pins. cannot get a working compilation. Marlin\src\feature\bltouch.cpp:96:36: error: 'PROBE_TRIGGERED' was not declared in this scope is the error I get
Last reply by pollyprinter, -
Help
by DylanFlame54-
- 2 replies
- 148 views
I recently installed a skr mini e3 v3 in my ender 3. I compiled the firmware for it, and it runs great but for some reason the part cooling fan is constantly on, and I can't turn it off. I can increase the speed slightly by turning the fan to full on the screen.
Last reply by knelezen, -
-
- 3 replies
- 298 views
i bought a printer about 2 months ago, Ive got 3 prints out of it since purchase and have emailed these people like crazy. The couple of responses i got in the beginning weren't quick but they did get back with me and sent me a new theirmistor wire. The wire i received is broke. I've emailed and nobody has bothered to reply to me. This company literally throws their products out the door then doesn't back their products at all. If you buy something from them then you better hope it never breaks. If it does your best option is to throw it in the trash because their support is terrible! I cant even get a reply back for simple questions. If you do get lucky enough to get som…
Last reply by Coco-BQ Team, -
-
- 1 reply
- 146 views
I had neopixels working in early version of marlin 2 on my skr pro 1.2 now with changes to VS code and marlin 2 bug fix I lost the use of my neopixels. Has anyone worked this out? or what pin could I use to get the neopixels working again. I was using pf 8 but it won't build using that pin out. Joe May
Last reply by Coco-BQ Team, -
-
-
- 2 replies
- 187 views
Hi all, After solving my Problem with the V2 SKR-Mini E3 board, I was faced with a new Problem. Taking the given Marlin version from Bigtreetech, adapting it for my Ender 3d Pro With the REVO Hemera Print head( seems to be the same as the Revo from Bigtreetech). Everything works fine till the first Print. Mesh-Bedleveling fine. PID-Tuning also works fine. I startet with my first Print the lin_advance test print. This works fine too. Than I tried to start a calibration Cube to test Flow an Meassurement. Nothing works. The first layer was fine and then suddenly the Extruder spooled out much more filament then for the first layer. It seems as if the …
Last reply by Coco-BQ Team, -
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
- 0 replies
- 5 views
-
- 1 reply
- 89 views
-
- 1 reply
- 141 views
-
- 1 reply
- 50 views
-
- 0 replies
- 23 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
No files have been downloaded yet this week.
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
