Other Accessories
726 topics in this forum
-
- 3 replies
- 884 views
Hello, I just purchased the PI4B adapter board and CB1 to run Klipper on my Ender-3 S1 Plus. I installed BQ's version of the Klipper/Mainsail and got it up and running with my printer. I just received the BTT HDMI7 V1.0 screen today in order to have Klipperscreen on it and to be able to use the touchscreen for local control. The image is there and it looks great but I can not get the touchscreen to work. I touch it but there is no response. I have it hooked up via HDMI to the PI4B/CB1. But no response with any screen touches. Is there something I am missing? Is there a setup in Mainstream or the Klipper config in order to activate the touchscreen portion? Th…
Last reply by DaVinci007, -
- 0 replies
- 159 views
The Raspberry Pad 5 seems like the perfect screen to add to my new Klipper setup. Right now, I have the HDMI5 but the lack of "hidden cables" installation makes me want to change it for the Raspberry Pad 5. Unfortunately, the Pad 5 shows support only for CB4. My current setup is: SKR Mini E3 V3 + CM1 + Pi4B Adapter + HDMI5 IPS LCD So, can I do: SKR Mini E3 V3 + Raspberry Pad 5 + CM1 ? Thank you!
Last reply by DaVinci007, -
- 0 replies
- 185 views
Can you use a BTT-CB1 and RPi 4 adaptor to replace an RPi 4 in an existing Voron 2.4 and use the existing controller? IE - Fysetc Spider or an Octopus
Last reply by WarHammer, -
- 0 replies
- 183 views
Be careful the CNA BUS connectors on the U2C and EBB42 are mirrored. I discovered this with some explosive results on my EBB42 board. It's fully my fault, but I just don't want anyone else going down this route of destruction. Hopefully in the future they could have a caution notice in the manual.
Last reply by Greg Nuspel, -
- 1 reply
- 910 views
First off sorry for the dump of information I've been looking at this stuff wayyy to long and I think it's getting to me. Also thanks for any help that can be provided. Following the instructions here it seems pretty straightforward. Yet I've had no success. I've tried to follow both the guide here in the 31865 Manual which doesn't work and Marlin warns you the methods mentioned here are being depreciated. I've also tried using the guide here in the H2 500c Manual. This one seems to be the more up to date instructions. When I compile the firmware using these instructions the terminal gives me the below WARN. …
Last reply by Salsped, -
- 0 replies
- 305 views
Hello, Does anyone have EZ31865 with Klipper running? What do I have to enter in Printer.cfg? Board BTT Octopus Max EZ. Thank you.
Last reply by tomix, -
- 2 replies
- 1.2k views
Hi, Currently the BIGTREETECH github for the SKR Mini E3 V3.0 has firmware for Ender 3 and Ender 5 while the Marlin source code has example config files for the CR-10S for the SKR Mini E3 V2.0 but not 3.0. I have a completely stock CR-10S and just got the SKR Mini E3 V3.0. As someone with very little experience editing firmware configuration files, how easy would it be to edit the Marlin example config files for the SKR Mini V2.0 for the V3.0? I'm thinking I basically just need to edit the new motherboard specific stuff from the source code from BIGTREE for Ender3.0 into the existing CR-10S V2.0 example code to deal with the difference in processor and fan setup (and…
Last reply by PrinceRoxasXIII, -
- 0 replies
- 129 views
I have setup the tf cloud module and can see it connected to my router but it only lets me connect for a minute while plugged into the card slot. It is connected to an skr 1.4 turbo. Still shows connected to my router but can't access via PC after a few minutes of it being on. Have to restart it every time. Haven't been able to find any real answers in other forums and this just seems like a waste of money at this point. Am I missing something?
Last reply by lmil0315, -
- 7 replies
- 1.3k views
Hello, I have a Manta M8P with the CB1 attached. I'm using the latest image, downloaded yesterday from BTT for the CB1 with klipper. after I wrote it to a sd card and loaded it and compiled it on the CB1 I created the output file klipper.bin, downloaded that and renamed it to firmware.bin and put it on a new sd card and placed that card into the MCU card slot on the Manta. After waiting several minutes, I checked Mainsail and it still wasn't connecting to the MCU, I pulled the card and checked it, the file wasn't renamed to firmware.CUR so I know it didn't take. Is there a step I'm missing or is there an issue with the latest image from BTT for the CB1 w/ klipper? …
Last reply by Fatkitties, -
- 3 replies
- 1.4k views
Hello I have had a few issues with my new BIQU BX printer. The OctoBTT # octopi-0170-with-octobtt image would not load on a Pi 4B 4 MB It errors out says I need to use a newer version? I have loaded the newer version of octo print it loaded fine no errors Once loaded I installed OctoBTT loaded on reboot so I installed it on the printer as per the Directions. Would not show on the screen . however was able to connect to octoprint and see the printer and start a job. Still could not connect to the pi dash on the printer. I made the changes required in the guide on GitHub. Cura profile …
Last reply by MDR, -
- 1 reply
- 322 views
Can somebody tells us what the configuration parameters are for the NTC100K thermistor which is shipped with the H2 V2S Lite Extruder? There is no info about it on the website and manual. What we need: the Beta model coefficient value (and C coefficient if needed for this model). For example: H2 V2S Lite extruder The thermistor resistance at 25 degrees Celcius is probably: 100000 But we need the Beta model coefficient too!
Last reply by Coco-BQ Team, -
-
- 2 replies
- 274 views
I have a BIGTREETECH BTT PITFT50 V1.0 Touch Screen 5 Inch LCD Display and I cannot get it to work. The calibration is off. I had it working with OctoDash, but then I had to reinstall the software and now the calibration is not working so I can not complete the OctoDash setup wizard. Does anyone know how to calibrate this screen?
Last reply by ZK66, -
-
- 3 replies
- 747 views
I have a Biqu H2 500c extruder that has worked perfectly for a couple of months. Now all of a sudden every print I try starts off fine but several minutes into the print the extruder stops extruding correctly, almost like it is blocked. However, when i try to manually extrude it extrudes okay but sometimes i feel a "slip" on the grip. I have already dissasemblerd the H2 unit and checked the teeth on the grear and I think they look okay. I even slighly extended the spring to apply more force to the filament just in case. Same result. I literally do not understand what is going on. Each new print starts and prints fine, then correct extrusion stops a num…
Last reply by Coco-BQ Team, -
- 1 reply
- 166 views
Hi, So I have a major problem with my TFT V3. Ive had it storage, packed up due to moving. Ive only recently acquired it from lock up and now it doesnt display. i can hear it boot and the touch works but im not getting any display. Can anyone help or suggest anything.. Ive tryed updating the firmware.. With and without the screen/Touch connected and still nothing. Thanks, Mike.
Last reply by Coco-BQ Team, -
- 7 replies
- 3.3k views
I upgraded my CR-10v3 with a SKR Mini E3 v3.0 and a TFT35 E3. Marlin Mode is working fine, but I can't get touchscreen Mode to work. It only says "No Printer Attached". I tried: Baudrate 250000 and 115200 upgrading firmware on both the board and tft serial port as -1 and 2 and serial port 2 as -1 and 1 I can connect to the printer via Printer face after updating my USB drivers and the firmware. What else is there to test? Any help is appreciated. Edit: i also checked the Pins with the schematics. Seems to be correct.
Last reply by BOR Designs, -
-
- 3 replies
- 546 views
hi, how to adjust the babystep being printed on a biqu b1 se plus (marlin). Any help would be appreciated. Thanks in advance
Last reply by rich342, -
-
- 1 reply
- 590 views
Is there anywhere I can download step files for the H2 and Ender 3 brackets for the BIQU microprobe?
Last reply by smatthew, -
- 0 replies
- 142 views
Bonjour à tous je galère à faire fonctionner un détecteur de filament "Smart filament sensor Bigtreetech sur une imprimante Flsun SR équipée d'un écran Bigtreetech TFT70. J'ai fait les modifications décrites dans le fichier d'aide de Bigtreetech. Mais l'icône n'apparaît pas sur l'interface de l'écran. Quelqu'un a déjà configuré ce setup ? Merci
Last reply by nomaifr, -
- 4 replies
- 275 views
I bought a BIQU B1 SE PLUS and I would like to know if a BIQU H2 v2 extruder can be installed and how to install it? Please it would be very nice to answer me.
Last reply by Mike Anderson, -
- 0 replies
- 170 views
This is the 2nd time today that the nozzle on my H2 V2s revo has jammed with no filament coming out of the nozzle was printing at 220c and inside an enclosure that had a steady 30.4c. Why would it just stop extruding its a direct drive had done 8 hours of a 2 day print.
Last reply by Bappi, -
- 0 replies
- 157 views
I did not want to plug it wlin without asking. I don't have the 115v 230v switch. Peeled of sticker to look. Am I safe to plug in?
Last reply by Vangal, -
- 0 replies
- 295 views
Hello, I'm interested to buy an Octopus PRO 1.0 and add the bed leveling MicroProbe. I have in my original printer a BL Touch but I'm not so happy because all plastic and it is not so precise, often I have to modify the Z preset in order to print well. Where I can find specs related to MicroProbe? I mean, I would like to know if the sensor is optic like CR Touch or magnetic like BL Touch. In the details page in BiQu web site there are a lot of info but the type of sensor I'm not able to find. Thanks Bye Andrea
Last reply by Andrea Guglielmi, -
- 2 replies
- 377 views
I recently installed the TFT35 E3 V3 onto my Ender 3. Many of the functions are simple enough to figure out. But some, I cannot figure out how to use. I cannot find anything online anywhere that gives any type of instructions as to actually use the display. I'm using the full color touch screen option. Where can I find user instructions? Right now, I just want to extrude. I can find all the settings, but nothing to actually tell it to go. Help?
Last reply by Lewis Douglas, -
- 0 replies
- 203 views
is it possible to download the exiting binary data from a TFT35 E£ V3 display in order to reinstate it if required. Kind regards Peter
Last reply by Peter G, -
- 0 replies
- 208 views
i have a skr mini E3 V2 and TFT35 E3 V3 in my ender 3. i have been attempting to get the z offset wizard to show in the ABL section in the menu. the icon does not appear in the touch side of the control. however when i switch to marlin mode i can toggle down. everything is enabled in the firmware correctly im assuming since i can use the wizard in the marlin mode. firmware on board is Marlin Bugfix-2.0.8.2.x
Last reply by Donny,
.png.e5d07c9bcf1ce7ca36ee414d56cbd468.png)
-
Popular Topics
-
Very unstable connection when Manta M8P/CB1 is directly connected to my PC via an ethernet cable
By zach,
- 4 replies
- 548 views
-
- 0 replies
- 1 view
-
- 0 replies
- 1,279 views
-
- 0 replies
- 1,982 views
-
- 2 replies
- 597 views
-
Announcements
-
Online Store
BIGTREETECH Documentation
https://bigtreetech.github.io/docs
If you have any issues with the product, please submit a support ticket.
https://biqu3d.com/pages/submit-a-ticket
-
Top Downloads
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
Free
-
