Jump to content

Other Accessories

714 topics in this forum

  1. SaMakerLab

    TEMPERATURE UNSTABLE ISSUE ON BTT E3 RRF WITH E3D V6.

    by SaMakerLab
    • 0 replies
    • 243 views

    I have a issue on BTT E3 RRF with temperature HOTEND while printing also after execute an auto PID tune. I have a E3D V6 HOTEND and I configured Marlin 2.0.9.3 with: #define TEMP_SENSOR_0 5 When I print I obtain this temperature graphic:

    SaMakerLab
    Last reply by SaMakerLab,
  2. Maurizio Marcellusi

    Impossible to install Klipper on BTT_SKR 1.4 Turbo V 2

    by Maurizio Marcellusi
    • 0 replies
    • 208 views

    How may I resolve this issue? Klipper installation stops as it starts to write on the Mainboard!

    Maurizio Marcellusi
    Last reply by Maurizio Marcellusi,
  3. Tomas

    Displays that can be used with SKR MINI E3 V3

    by Tomas
    • 1 reply
    • 274 views

    Hello. I would like to know, what display could be used with SKR MINI E3 V3 motherboards. I know about BTT 2,4 TFT and 3,5 TFT, but I dont like "touch screen" features and Im not sure about Marlin FW support these displays. Is it possible to use BTT MINI 12864 v1.0 (voron) with propper cable reduction (EXP1 and EXP2 into EXP3)

    BTT Tony
    Last reply by BTT Tony,
  4. jamesmhoward

    Skr Mini E3 V3.0 with Ezabl pro

    by jamesmhoward
    • 3 replies
    • 305 views

    Hello everyone, So picked up the new skr v3.0 and have been through 1 headache after another...finally got everything running only to find out its the firmware for bl touch....can anyone help me with the firmware for Ezabl pro??

    cul8rmom1
    Last reply by cul8rmom1,
  5. cdPrint

    Flash klipper on skr mini e3 V3

    by cdPrint
    • 1 reply
    • 1.2k views

    I have v2 now, getting V3 tomorrow and have question These instructions work for V2, i tried. The bootloader offset has to be set to 28kib https://docs.vorondesign.com/build/software/miniE3_v20_klipper.html however, your github for V3 says offset should be 8Kib https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper Is 8Kib correct?

    BTT Tony
    Last reply by BTT Tony,
  6. cdPrint

    Ender 5

    by cdPrint
    • 1 reply
    • 189 views

    I have the stock ender 5 pro display. I want to use it with klipper and the SKR E3 MINI V3 Can you please provide the correct [display] section for the klipper config? Thank you.

    BTT Tony
    Last reply by BTT Tony,
  7. Derek

    sensorless homing

    by Derek
    • 1 reply
    • 275 views

    hey I just wanted to know how to enact the sensorless homing feature on my ender 3 pro.

    BTT Tony
    Last reply by BTT Tony,
  8. pazza

    octoboard v1.1

    by pazza
    • 1 reply
    • 338 views

    Hi need some I got a octo 1.1 board.. once I configuered the board and files for Klopper and did sanity test I can't get the motors to work ( I used mutimeter to test motors they are all fine.. I tried all suggstions , and sanity test but nothing works to move the motors .. so I say I might have blown something on the board..fuses are fine too. Any help would be appreciated

    BTT Tony
    Last reply by BTT Tony,
  9. brandt_ender3

    SKR MINI E3 V2 Reboot / Crashes when hot end or bed is heated past room temp.

    by brandt_ender3
    • 1 reply
    • 181 views

    Ive been using my Ender 3 V1 with the skr mini 3 v2 and touch screen for about 4 months now, no problem. Last night it stopped mid print and ever since it will not allow itself to heat up past room temp. It does indicate the temp as being 20ish for both the hot end and the bed, but once I pre-heat past the temp even 1 degree it either completely crashes or it reboots. Im at a loss as to what could be the problem. I suspected the thermistor, but from what I've read its unlikely its that if it shows the room temp correctly (this could also be wrong). Any help would be appreciated! Thanks!

    BTT Tony
    Last reply by BTT Tony,
  10. Spelucker

    tft-24 v1.1 only the display backlight works

    by Spelucker
    • 1 reply
    • 261 views

    I buy and connect the display to the scr 1.3 board, and only the backlight works, I need help

    BTT Tony
    Last reply by BTT Tony,
  11. Callisto

    BTT SKR2 Rev. A and Klipper

    by Callisto
    • 1 reply
    • 217 views

    Good morning @all... I will swap from Octopi & marlin 2.0 to mainsailos & klipper... Now my question. I have a BTT SKR2 Rev. A with TMC2209 sensorless homing , fixed the known issue with the Rev. A Board with jumper wires and disable by uncommenting #define DISABLE_DRIVER_SAFE_POWER_PROTECTION.......... What i have to do to safely run the Rev. A Board and TMC 2209 with sensorless homing and Klipper .... I fixed the Board to Use it with Marlin like BTT wrote last year and with Marlin it works just fine for all the time since it is instslled Option 1: Use 1 or 2 Dupont jumper wires (two jumper wires are recommended since they will be able to carry higher…

    BIQU
    Last reply by BIQU,
  12. vgaggia

    SKR 2 SD Card/Firmware Issue

    by vgaggia
    • 2 replies
    • 531 views

    So i've been trying to flash a firmware.bin with the sd card, but it seems that the board refuses to read the sd card, is there anything i can do, this is a brand new board(literally like 2 days old), the LCD also says printer disconnected for some reason The board is a Bigtreetech SKR 2, the LCD is a Bigtreetech TFT35 v3.0, i'm using Bigtreetech Stepstick Mute TMC2208 V3.08 drivers and a stock ender 5 plus power supply. The SD Card i'm using is a netac 8gb microsd card, i've tried using pre-compiled firmwares and i've tried compiling my own, nothing works, if the board is defective, how do i go about getting a replacement, i live in south africa so obviously ship…

    vgaggia
    Last reply by vgaggia,
  13. DinWilliam

    SKR 2 wont start

    by DinWilliam
    • 1 reply
    • 226 views

    Help Just installed SKR 2 on my ender 5 but after turning it on there is only blue screen on the LED. If i connect my TFT35 it just says "printer not recognised". Constant red led light on the board. Please help.

    BTT Tony
    Last reply by BTT Tony,
  14. Randall Blake

    B1 SE Plus forgot where home is!

    by Randall Blake
    • 1 reply
    • 774 views

    I've had a B1 SE Plus since last November. It has worked fine until now. I noticed that the bed was not level (extruder nozzle too close on the right hand side). I tried to set the Z-Offset using a Cura plugin. That seemed to work for a while, but now, my printer cannot find "Home" . It stops about 20-30 mm above the bed and reports that the home operation failed. It tells me to "reset". (The message is: "PRINTER HALTED Please Reset Homing Failed") I assume "please reset" means revert to factory defaults. (It might mean just "turn off the printer" - but I've done both. Neither fixes the problem.) Further, when I try to use "Baby Steps", all settings seem to RAISE the no…

    BTT Tony
    Last reply by BTT Tony,
  15. Mike Eichacker

    New B1 heatbed heats immediately on power up

    by Mike Eichacker
    • 1 reply
    • 231 views

    New B1 heated bed heats immediately on power up - troubleshooting steps?

    BTT Tony
    Last reply by BTT Tony,
  16. Arturo Caballero

    Microstepping on SKR2 with TMC2209

    by Arturo Caballero
    • 1 reply
    • 414 views

    I understood that you could program the microstepping in TMC2209's by using the UART interface. I connected the UART jumper as shown in the user guide. However, I can't change the microsteps by changing $150. In fact $150 shows 16 but in reality the motor moves as if it was 8. If I can't change $150 it remains at 16. The only way I can change the microsteps is with the jumpers on MS1 and MS2. How can I change the microsteps with the UART interface?

    BTT Tony
    Last reply by BTT Tony,
  17. Carsten Hagen

    SKR 1.4 no Fan Control on Fan0

    by Carsten Hagen
    • 1 reply
    • 218 views

    Hi, my BTT KSR 1.4 has no control to the Fan on FAN0. It is always on when the board has power. I cannot control the fan via M106. I cannot turn off the power (0%) and I cannot reduce the Fan Speed (25%, 50%, 75%...). What to do? Marlin is used and settings are already checked.

    BTT Tony
    Last reply by BTT Tony,
  18. AWESOMEka001

    BIGTREE TECH smart filament sensor not working

    by AWESOMEka001
    • 1 reply
    • 246 views

    Hello. I am using an SKR 2 and a tft35v3 and just bought a smart filament sensor, I have followed the instruction manual and have wired it up to e0fildet on my main board. I compiled the firmware and it is not detecting. When I send m119 it says open but when I move the filament ~7mm through it goes to TRIGGERED and then back once I move it more. Does anyone know why this is happening? Thanks.

    BTT Tony
    Last reply by BTT Tony,
  19. Faruk Sutar

    SKR 2.0 STM32F429 Firmware

    by Faruk Sutar
    • 2 replies
    • 613 views

    I have purchased a SKR 2 Controller Board. I did some changes in Merlin 2.0 code, in configuration.h file and recompiled code through VSCode, platformio… In new board instead of uploading “firmware.bin” file through SD Card, I uploaded a “firmware .bin” through STM’s “ST Link Programmer”… Now its not accepting any of the firmware through SD card.. May be bootloader or STM32F429’s program is erased… Can you please provide SKR 2’s (STM32F429) firmware/bootloader file(s) by which board can be restored to original? It will be great help for me, as I am stucked to the basic thing and I have to dispatch the 3D printer …

    Faruk Sutar
    Last reply by Faruk Sutar,
    • Like
  20. davidm

    Trying to build new firmware for BIGTREETECH SKR Mini E3 V2.0 Control Board, with TFT35 E3 V3.0 Graphic Smart Display Controller

    by davidm
    • 2 replies
    • 402 views

    Hi, I'm trying to build a new version of the Marlin 2.0.9.3 firmware for my Ender 5. I grabbed the latest Marlin tarball build, the _Bootscreen.h Configuration_adv.h Configuration.h and _Statusscreen.h from here and dropped them into the Marlin-2.0.x/Marlin directory. I installed Visual Studio, and platormio and Auto build Marlin for the Linux platform. I followed the instructions for building Marlin and I got a screen too many choices for firmware and they all build. There are 8 Environments offered and they all build, which is the correct one? Firmware: Marlin 2.0.9.3 Config by:(KuranKaname, Ender-5 Pro) Machine Name: Ender-5 Pro Extruders:…

    davidm
    Last reply by davidm,
  21. dcryder

    ender 3 v2 upgrade ?s

    by dcryder
    • 1 reply
    • 280 views

    I bought a BTT TFT43 v3 screen and a filament sensor and biotech bed level sensor and in my earlier question you told me my motherboard might not support the touch screen. so my question is what mother board do you suggest I get? I would like to upgrade at later point to a 2 into 1 extruder.

    BTT Tony
    Last reply by BTT Tony,
  22. beantree

    SKR v1.4 Turbo burned out component

    by beantree
    • 1 reply
    • 242 views

    Help! My board made smoke and glowed very bright. The toasted component is shown in the picture. Either a regulator or, maybe a mosfet. I understand that I have probably done something to cause this. I just wonder if someone can give me a clue as to what might cause this so that I can make sure it doesn't happen again when I get my replacement board? Thanks

    BTT Tony
    Last reply by BTT Tony,
  23. Fisisist

    thermistor causes board not to recognize printer

    by Fisisist
    • 1 reply
    • 272 views

    If the nozzle and bed thermistor (stock thermistors) for my Artillery Sidewinder X1 are plugged in, the display shows the printer is not recognized. If I disconnect the thermistors, it recognizes the printer. Any thoughts on this issue?

    BTT Tony
    Last reply by BTT Tony,
  24. Taomyn

    Cannot flash firmware to new Mini E3 v3

    by Taomyn
    • 5 replies
    • 515 views

    I just got a new Mini E3 v3 for my Ender 3 Pro, which previously had a Mini E3 v1.2 for over a year but I needed that board for another project. The new board powers up and I get Marlin loaded and can access things through the screen just fine. But when I try to flash a new firmware by placing a newly formatted 2GB SD card with firmware.bin nothing happens during the next power up and I still have the same version. I have tried both my own compilation of Marlin and also the the latest from the BTT Github (normal and the one for BL-Touch for Z-homing). The SD card LED lights green when the card is inserted, so I know it's being detected, the other two LEDs, the status…

    BTT Tony
    Last reply by BTT Tony,
  25. wasabi

    SKR Pico max power for heated bed?

    by wasabi
    • 1 reply
    • 593 views

    The documentation doesn't mention what's the maximum supported wattage for heated beds. Could you please clarify this information?

    BTT Tony
    Last reply by BTT Tony,
×
×
  • Create New...