Jump to content

General Discussion

136 topics in this forum

  1. EmperorPenguin

    CR-10S Upgrade Help!

    by EmperorPenguin
    • 1 reply
    • 310 views

    I have a CR-10S with an old 12V mainboard. I want to add auto leveling to it. I was thinking about installing a BTT SKR 2 Rev B mainboard. I was wondering if I could add a CR Touch with this board. If not, will a BL Touch work with it? Thank you in advance for any help you could give me!!

    BIQU info
    Last reply by BIQU info,
  2. gorch

    Upgrading a Creality Ender 5 Plus. need help selecting components

    by gorch
    • 2 replies
    • 395 views

    Hello Guys, I would like to upgrade and rewire my Creality Ender 5 Plus. I searched for some components on the website of biqu. and I would like to know if these parts are compatible. I will also buy a raspberry 4 board to complete the setup. i incl. an image. if I need more boards and stuff please let me know. I want to build the ultimate ender 5 can version. money not an issue. its a fun project for me. and I will document everything to maybe inspire more people.

    gorch
    Last reply by gorch,
  3. Sim

    BTT TMC2209 Drivers

    by Sim
    • 1 reply
    • 376 views

    I'm working on Octopus Pro V1.0 Motherboard and i have to use TMC2209 stepper drivers, so now, my question is, can i use Lerdge TMC2209 stepper drivers instead of BTT TMC2209 stepper drivers ?? Are they (lerdge TMC2209 stepper driver) compatible with Octopus Pro V1.0 Motherboard ??

    BIQU info
    Last reply by BIQU info,
  4. dalogan

    SKR2 Shutdown

    by dalogan
    • 1 reply
    • 295 views

    I have problems with my new SKR2 motherboard , has the MCU STM32F429VGT6 rev b, when i am working it is shutdown every 5 minuts. Marlin firmware is correct. Is there posibily that the mcu is not upgraded? Thanks Regards

    BTT Tony
    Last reply by BTT Tony,
  5. Ken Hooper

    Service01@ Address are full

    by Ken Hooper
    • 1 reply
    • 301 views

    This is the bounce email. How do you all answer or help anyone . I love what you have done with the BX printer great design but I'm losing my confidence in your company. I have several of your boards for upgrading a few of my older printers but I'm not confident in your support. 很抱歉您发送的邮件被退回，以下是该邮件的相关信息： 被退回邮件 主 题：Several Issues with BIQU BX printer 时 间：2022-02-25 04:46:34 无法发送到 service01@biqu3d.com 退信原因 收件人（service01@biqu3d.com）邮箱空间不足，不能接收你的邮件。 解决方案 请通知你的收件人清理邮箱空间，或去掉邮件中的大附件。 …

    BTT Tony
    Last reply by BTT Tony,
  6. Togirix

    connector NEOPIXEL on BTT TFT70 V3.0

    by Togirix
    • 2 replies
    • 461 views

    Hello, I'm frechy, On a BTT TFT70 v3.0, I would like to know the maximum current that the NEOPIXEL connector can provide at the output to possibly connect a leds-type ring. I have not been able to find this information in your documentation. Thank you part advance for your answer. Sincerely, Jean luc Golion.

    Togirix
    Last reply by Togirix,
  7. Carlos Guimaraes

    SRK-2

    by Carlos Guimaraes
    • 1 reply
    • 411 views

    Bom dia Srs. Recentemente adquiri uma placa BIGTREETEC SKR-2 Rev-B e por um infeliz acidente ela estava numa caixa com outras peças e dois dos pinos do chip se quebraram. Comprei uma nova peças STM32F407VGT6 e coloquei no lugar, acontece que ela não está conectando via USB e nem reconhece o cartão SD segundo informações preciso do arquivo de BOOTLOADER. Seria possível que alguem pudesse me ajudar e disponibilizar este arquivo "Bootloader.ini" para que pudesse recuperar minha placa. Obrigado a todos.

    BTT Tony
    Last reply by BTT Tony,
  8. billtodd

    BTT-TFT35 Controlling an external bed heater via serial port

    by billtodd
    • 4 replies
    • 515 views

    I'm building a segmented heated bed for my printer (yes, I pinched the idea from Prusa ;-)) The bed will have nine segments (100x120 to give an approximate 300x360 bed) . The segments heaters will be controlled by a Raspberry-PI PICO based DIY controller. I'd like to be able to control the temperature and selection of segments from my BTT TFT 35 (Great device BTW :-)) either directly or via my BTT octopus board . To do this I need to be able to route the temperature data to and from a spare serial port . Any guides or ideas how I might achieve this? Ideally I'd like to add a bed control page to the TFT menu which would allow selection of which segments a…

    billtodd
    Last reply by billtodd,
  9. Randall Sam

    SKR MINI E3 V2 board doesn't boot up when turned on

    by Randall Sam
    • 2 replies
    • 333 views

    I was in the middle of heating up the printer when I noticed the screen froze. So I turned off the printer and then turned it back on again after awhile, but my screen just remains blue. I tried reflashing the original firmware for the board but it doesn't want to flash. I checked the forums and noticed a lot of other people have had the same issues with their boards as well. Any advice on how to fix this issue

    BTT Tony
    Last reply by BTT Tony,
  10. Scott Oliver

    SKR Mini E3 V1.2 Firmware on ender 3

    by Scott Oliver
    • 1 reply
    • 486 views

    I hope this is the right site. I am looking for firmware for the Ender3. This github says its for Ender 5. Will it work on the 3? https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware

    BIQU
    Last reply by BIQU,
  11. Fred

    Documentation?

    by Fred
    • 1 reply
    • 867 views

    Getting my 1st 3D printer, recommended by someone who is not at his first and got a B1. All reviews I've read says those are 1st timers 3D printer but both the website and the documentation are very poor on anything. I could detail what I'm expecting but.. at least set up a wiki, put some stuff in place to grow a community. Maybe hire a community manager? Le's say I hope more is coming 🙂 oh.. and this will benefit you both in terms of supported products and .. sales as people will understand what upgrade/options does what and why it's a good choice. Thanks.

    BIQU
    Last reply by BIQU,
×
×
  • Create New...