Jump to content

SKR 3 no communication with TMC2209


Tiko
 Share

Recommended Posts

Upgrading from SKR 1.4. TMC2209 on all axes. Installed all jumpers according to manual.

Sensorless homing not working.

Send: M122
Recv: 		X	Y	Z	E	E1
Recv: Address		0	0	0	0	0
Recv: Enabled		false	false	false	false	false
Recv: Set current	800	800	800	800	800
Recv: RMS current	1436	1436	1436	1436	1436
Recv: MAX current	2025	2025	2025	2025	2025
Recv: Run current	25/31	25/31	25/31	25/31	25/31
Recv: Hold current	12/31	12/31	12/31	12/31	12/31
Recv: CS actual	0/31	0/31	0/31	0/31	0/31
Recv: PWM scale
Recv: vsense		0=.325	0=.325	0=.325	0=.325	0=.325
Recv: stealthChop	false	false	false	false	false
Recv: msteps		256	256	256	256	256
Recv: interp		false	false	false	false	false
Recv: tstep		0	0	0	0	0
Recv: PWM thresh.	1756	1756	10541	3077	3077
Recv: [mm/s]		90	90	3	30	30
Recv: OT prewarn	false	false	false	false	false
Recv: triggered
Recv:  OTP		false	false	false	false	false
Recv: pwm scale sum	0	0	0	0	0
Recv: pwm scale auto	0	0	0	0	0
Recv: pwm offset auto	0	0	0	0	0
Recv: pwm grad auto	0	0	0	0	0
Recv: off time	0	0	0	0	0
Recv: blank time	16	16	16	16	16
Recv: hysteresis
Recv:  -end		-3	-3	-3	-3	-3
Recv:  -start		1	1	1	1	1
Recv: Stallguard thrs	80	70	0	0	0
Recv: uStep count	0	0	0	0	0
Recv: DRVSTATUS	X	Y	Z	E	E1
Recv: sg_result	0	0	0	0	0
Recv: stst		*	*	*	*	*
Recv: olb
Recv: ola
Recv: s2gb
Recv: s2ga
Recv: otpw
Recv: ot
Recv: 157C
Recv: 150C
Recv: 143C
Recv: 120C
Recv: s2vsa
Recv: s2vsb
Recv: Driver registers:
Recv: 		X	0x00:00:00:00	 Bad response!
Recv: 		Y	0x00:00:00:00	 Bad response!
Recv: 		Z	0x00:00:00:00	 Bad response!
Recv: 		E	0x00:00:00:00	 Bad response!
Recv: 		E1	0x00:00:00:00	 Bad response!
Recv: 
Recv: 
Recv: Testing X connection... Error: All LOW
Recv: Testing Y connection... Error: All LOW
Recv: Testing Z connection... Error: All LOW
Recv: Testing E connection... Error: All LOW
Recv: Testing E1 connection... Error: All LOW

 

Link to comment
Share on other sites

  • 1 month later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...