Other Products
15 topics in this forum
-
- 0 replies
- 3 views
Hello all. I recently purchased the Hermit to install on my Any Cubic Chiron. I'm curious what hotends people have installed with this tool? i was considering using the V6 volcanos I already have is there a bracket that would work with the hermit?
Last reply by micheal Keith, -
- 1 follower
- 0 replies
- 8 views
Hello. Before buying a hermit crab tool changer i'd like to know how is the fixed plate attached to the bearing block, and how can i attach the belts to it. I could not find information on BQ site nor internet. My printer is a custom coreXY, with XY linear rails and triple Z axis Thank you
Last reply by rmd, -
- 0 replies
- 10 views
I can't seem to find the Operation Temperature Range for this board in manual. Could someone point me in the right direction? Thanks.
Last reply by Heath, -
- 1 follower
- 1 reply
- 25 views
Hi I have purchased an EBB36 and have noticed that the connectors are tiny. Can you confirm what they are? In particular the connector for the PT100 and the fans?
Last reply by Rhoades-Brown, -
- 2 replies
- 50 views
Hello, Is there any configuration documents like pins map or dts overlay parameters (using vc4-kms-dpi-generic with bad results) for using the PI TFT43-DIP on raspberry pi 3 ? Thank you Emmanuel
Last reply by Emmanuel, -
- 0 replies
- 20 views
Hi! So, I just purchased a SKR 3 EZ and Biqu H2 Smart Extruder to make something new out of my Anycubic Mega X. I intend to keep Klipper as the firmware (with a RPi 4) I've purchased as well the DCDC Mode, and here's where my questions begin: - I read somewhere that it would power the RPi 4 without any issues. What does exactly that power module do? I mean, I know it stabilizes 5v (in this case)... but where? I have 24v fans connected to FAN0 and FAN1. - How do I connect the RPi directly to SKR 3? Through TFT pins, even for power? In that case, does the DCDC Mode do anything? I feel that there is little to almost no information regarding the …
Last reply by Tendeiro, -
- 15 replies
- 628 views
BIGTREETECH EBB 36/42 Can Bus It said ship with Random MCU Chip One of the chip don't support CAN Bus 36 vs 42 the different is the AMP it can handle like the mellow one? 5 vs 9 amp? Where can I find more info on this? or how to connect to my Pi and Octopus 1.1 Thank you
Last reply by Rula, -
- 1 follower
- 4 replies
- 340 views
Last reply by Eric, -
- 4 replies
- 44 views
I recently purchased two Raspberry Pad 5 for Compute Module 4 in two seperate orders. I received one of them and tried to make it work, but i am facing network issue. I flashed mainsail OS to use Klipper for my Ender3 S1 Pro But my Pad5 is not able to get the correct IP Address from my router When I check the ip using ifconfig command it gives me something like this, 169.254.12.165 I tested exact same setup with my Raspberry pi 3B+, it worked fine. I tested the same the micro SD card and ethernet cable to both PAD5 and RPi3B+ PAD5 is always unable to get the correct ip address from my router can you help me out to solve this issue?
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
Last reply by BIQU info, -
- 1 reply
- 47 views
Does the Hermit Crab CAN kit work with the BTT SKR 2 mainboard or will I need something else? I do have an Octopus but I'm saving that for my Voron and it would be a very tight fit in my Ender 5 Plus enclosure anyway. If it doesn't work with the SKR 2, what other options might I have?
Last reply by BIQU info, -
- 2 replies
- 110 views
Hi! I recently purchased a Hermit Crab & an H2 extruder for my Ender 3 v2. I'm having a problem determining how to connect the Hermit Crab to my 4.2.7 motherboard. The provided wiring harness has a several unlabeled connectors and at least two (FLD & EO) which I haven't been able to determine what those acronyms refer to. Also, the concerning is that the manual has a picture of the PCB board interfaces connector wiring which doesn't match mine. The PCB-F illustration indicates that the BL TOUCH connector connects with the orange wire on the outside - mine connects with the orange wire at the other end. (Possibly it's just a mistake in the picture?) Picture …
Last reply by Stacking_Layers, -
- 1 reply
- 76 views
Hey! So i want to falsh the HermitCrab with the STM32 Programmer with a selfmade bin or hex file. But i dont get it working. I put it in DFU Mode and it shows as connected in the Programmer but after i set the bin or hex file and press start programming i get error everytime. Like this: 09:36:30 : Download in Progress: 09:36:31 : Error: Write failed at address: 0x8000800 09:36:31 : Error: failed to download Segment[0] 09:36:31 : Error: failed to download the File 09:36:31 : RUNNING Program ... 09:36:31 : Address: : 0x08000000
Last reply by BIQU info, -
- 1 reply
- 71 views
Hi, I recently bought my Biqu BX and I want to buy a hermit crab and it is not clear for me which model I should buy, could you recommend me the exact model? Thank you
.thumb.png.9197dea5817e24c2e148f40621f6d4aa.png)
Last reply by BTT Tony, -
- 7 replies
- 175 views
Hi, I just got the Smart Sensor and I'm pondering the use with flexible TPU filaments. It's very hard, if not impossible, to get the filament through the sensor. Any ideas on how to do this? I'll probably engineer a new back plate (need one for mounting anyway) and include some kind of knob or slider that compress the internal spring. Something for you to consider for a future product version maybe. //FNM
Last reply by FNM, -
- 5 replies
- 116 views
I have a CR 10 mini and and a SKR Mini E3 V2 as board and a TFT 35 as screen. I tried both options and did set everything right up. First I tried to plug it in E0-Stop on to the motherboard directly. Then i tried to plug it into the screen. here my configs files of Marlin and the Screen. https://github.com/bigtreetech/smart-filament-detection-module/files/8455734/configs.zip and I made the same post on github: https://github.com/bigtreetech/smart-filament-detection-module/issues/26
Last reply by Valiance,
.thumb.png.8a6b04bfa9af0ae76863d190ec8592cb.png)
.thumb.png.9197dea5817e24c2e148f40621f6d4aa.png)
